2026-10-15

高压电池（单相至三相）（改装）（电池置于操作台上）

校正代码 16010206 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See 人员保护 to make sure wearing proper PPE when performing the below procedure. NOTE: See 人体工程学注意事项 for safe and healthy working practices.

注
This procedure is to be performed if the HV battery has been removed and components must be reworked or swapped between old and new HV batteries. Add this correction code as a separate activity.
警告
Remove all jewelry (watches, bracelets, rings, necklaces, earrings, ID tags, piercings, etc.) from your person, and all objects (keys, coins, pens, pencils, tools, fasteners, etc.) from your pockets before performing any procedure that exposes you to high voltage.
警告
If corrective eyewear is necessary to safely perform any procedure, make sure that the eyewear is securely restrained to the head and cannot fall off.
警告

Only technicians who have completed all required certification courses are permitted to perform this procedure. Tesla recommends third party service provider technicians undergo equivalent training before performing this procedure. For more information on Tesla Technician requirements, or descriptions of the subject matter for third parties, see HV Certification Requirements. Proper personal protective equipment (PPE) and insulating HV gloves with a minimum rating of class 0 (1000V) must be worn at all times a high voltage cable, busbar, or fitting is handled. Refer to Tech Note TN-15-92-003, High Voltage Awareness Care Points for additional safety information.

程序

  1. 拆下旧高压电池上的三相功率转换系统。请参阅 功率转换系统（拆卸和更换）。
  2. 拆下新高压电池上的单相功率转换系统。请参阅 功率转换系统（拆卸和更换）。
  3. 拆下新的高压电池上的单相交流输入线束。请参阅 线束 - 交流输入 - 高压电池（拆卸和更换）。
  4. 将烟火电池断接开关螺栓（2 个）安装到旧高压电池的高压电池仓上并手动拧紧。
    注
    请勿安装烟火电池断接开关。仅安装螺栓。
  5. 将烟火电池断接开关绝缘子安装到烟火电池断接开关螺栓上。
  6. 将旧高压电池上的三相功率转换系统安装到新的高压电池上。请参阅 功率转换系统（拆卸和更换）。
  7. 将新的三相交流输入线束安装到新的高压电池上。请参阅 线束 - 交流输入 - 高压电池（拆卸和更换）。
  8. 将旧高压电池上的高压电池仓盖板安装到新的高压电池上。请参阅 盖板 - 高压电池仓（拆卸和更换） ((拆卸和更换))。
  9. 将新高压电池上的高压电池仓盖板安装到旧高压电池上。请参阅 盖板 - 高压电池仓（拆卸和更换） ((拆卸和更换))。
  10. 执行高压电池仓漏气测试。请参阅 高压电池仓漏气测试 (Inspection)。