08/11/2024 00:31:30
校正代码 16010231 注意:除非本程序中另有明确规定,否则上述校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。注意:请参阅平均维修工时,深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈,请发送电子邮件至LaborTimeFeedback@tesla.com。注意:请参阅人员保护,确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
- 2024-11-07: Added 3-phase harness disconnect/connect steps.
- 2024-06-13: Updated lift pad adapter PNs.
- 2023-11-21: Added new lift pad instructions.
- 2023-08-29: Updated EPB Service Mode reference.
警告
只有接受过高压安全意识培训并完成全部所需认证课程(如适用)的维修技工才允许执行此程序。处理高压线缆、母排或接头时,务必全程穿戴最低防护等级为 0 (1000V) 的适当个人防护装备 (PPE)及高压绝缘手套。有关其他安全信息,请参阅技术注意事项 TN-15-92-003,高压安全意识注意事项
。
警告
尽管此程序已经过验证,但仍是一个草案。可能没有警告和注意事项。请遵守安全要求,处理或靠近高压系统和部件时,请谨慎操作。请将校正修理内容及反馈发送至ServiceDevelopment@teslamotors.com。
拆卸
-
Release LH rocker cover from front and rear wheel liner
注4x clips
-
Remove LH rocker cover from rocker carrier
注11x clips, 11x tabs, Work a plastic trim tool between door panel and rocker cover to release tabs
-
Remove bolts securing LH rocker carrier to body
注2x bolts, 10mm, 5 Nm
-
Remove LH rocker carrier from body
注10x clips
-
Remove butyl patches covering LH rocker access holes
注2x butyl patches, Clean excess butyl from area
-
安装举升垫适配器。
- 仅适用于欧洲、中东和非洲:安装举升机垫适配器,Model 3 (1453419-00-A
- 其他地区:安装通用举升垫适配器 (1936724-00-A)。
警告请勿使用任何其他举升垫适配器。注欧洲、中东和非洲以外的地区:使用通用举升垫适配器 (1936724-00-A) 代替举升机垫适配器,Model 3 (1453419-00-A。请弃用任何其他版本的举升垫适配器。注通用举升垫适配器在欧洲、中东和非洲尚不可用。请确保在 Model Y 上使用 Model Y 橡胶举升垫,在 Model 3 上使用 Model 3 举升垫。通用举升垫适配器说明:
- 将与举升机类型相匹配的正确螺纹适配器安装到举升机适配器上。
- 确保将螺纹止动垫圈正确安装并紧固至举升机适配器底部。如果未安装螺纹止动垫圈,请勿继续使用举升机适配器。
- 将举升机适配器安装到举升臂上,使黑色的举升垫朝向车辆。警告确保适配器安装方向正确。
- 调整举升臂位置,使举升机适配器与车辆上的固定销孔对齐。
- 抬起举升臂,将举升垫完全放置到车辆上。
- 确保所有 4 个适配器均已完全就位在车辆上。
-
Remove clips securing RH rocker cover to front and rear wheel liner
注4x push clips
-
Remove RH rocker cover from rocker carrier
注11x clips, 11x tabs, Work a plastic trim tool between door panel and rocker cover to release tabs
-
Remove bolts securing RH rocker carrier to body
注2x bolts, 10mm, 5 Nm
-
Remove RH rocker carrier from body
注10x clips
-
Remove butyl patches covering RH rocker access holes
注2x butyl patches, Clean excess butyl from area
-
安装举升垫适配器。
- 仅适用于欧洲、中东和非洲:安装举升机垫适配器,Model 3 (1453419-00-A
- 其他地区:安装通用举升垫适配器 (1936724-00-A)。
警告请勿使用任何其他举升垫适配器。注欧洲、中东和非洲以外的地区:使用通用举升垫适配器 (1936724-00-A) 代替举升机垫适配器,Model 3 (1453419-00-A。请弃用任何其他版本的举升垫适配器。注通用举升垫适配器在欧洲、中东和非洲尚不可用。请确保在 Model Y 上使用 Model Y 橡胶举升垫,在 Model 3 上使用 Model 3 举升垫。通用举升垫适配器说明:
- 将与举升机类型相匹配的正确螺纹适配器安装到举升机适配器上。
- 确保将螺纹止动垫圈正确安装并紧固至举升机适配器底部。如果未安装螺纹止动垫圈,请勿继续使用举升机适配器。
- 将举升机适配器安装到举升臂上,使黑色的举升垫朝向车辆。警告确保适配器安装方向正确。
- 调整举升臂位置,使举升机适配器与车辆上的固定销孔对齐。
- 抬起举升臂,将举升垫完全放置到车辆上。
- 确保所有 4 个适配器均已完全就位在车辆上。
- Open all four doors
- Lower all four windows
-
Chock LH rear wheel
- Connect a laptop with Toolbox 3 to the vehicle.
- Enable the EPB Service Mode. See 驻车制动 - 钳 - 后 - LH(释放)
- Select ‘Actions/Autodiag’ and search for ‘Thermal’
-
Select ‘PROC_VCFRONT_X_THERMAL-FILL-DRAINSearch for routine in ToolboxThermal Fluid Fill/Drain’, click ‘Run’, and allow routine to complete
注This will ensure the octovalve is in the Series position, Coolant pumps will also be disabled, Once run is selected routine is in progress despite the prompt with loading circle, Routine will time out after several hours and return valves to parallel position if unattended, Select 'X' at top right of window to close once complete
-
Remove laptop from vehicle
注Do not close Toolbox 3.0, we will need to resume later
- Open the hood.
-
Remove the rear apron.
-
Remove LH IP end cap
注3x clips
-
Remove LH mid A-pillar assembly
注1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove
-
Remove clip securing LH lower A-pillar trim
注1x push clip
-
Remove LH lower A-pillar trim
注6x clips, 2 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release trim panel
-
Move LH front seat backward
注Ensure profile is saved to allow seat position to be restored
-
Remove screw and clips securing LH footwell cover
注2x push clips, 1x screw, T20, 2.5 Nm
-
Remove connectors from LH footwell cover and remove from vehicle
注3x tabs, 1x Ethernet connector, 1x puddle light connector
-
Remove LH front floormat
-
Remove LH console side panel carpet
注11x clips, 2x guide pins, Use trim tool starting at top edge to release upper clips, then pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged
-
Remove clip securing LH front cabin carpet to body
注1x clip
-
Fold LH front cabin carpet rearward
注Maneuver carpet below brake pedal and accelerator pedal, Newer Vins may be equipped with additional foam installed below carpet
-
Remove foam plugs to access LH front inner HV battery bolts
注2x plugs, Push pick through foam and turn roughly 45 degrees to grab onto foam insert and pull straight out, Newer vins may be equipped with 1x foam plug
-
Remove both LH front inner HV battery bolts
注2x bolts, EP20, 136 Nm
-
Raise LH front seat cushion to maximum height
注This will allow access to HV battery bolts at LH front foot well and below LH front seat
-
Remove RH IP end cap
注3x clips
-
Remove RH mid A-pillar assembly
注1x clip, 1x tab, Release the upper clip then pull mid A-pillar upward to remove
-
Remove clip securing RH lower A-pillar trim
注1x push clip
-
Remove RH lower A-pillar trim
注6x clips, 2 guide tabs, Pull rear of lower A-pillar upward to release clip then pull rearward to release trim panel
- Move the RH front seat back.
-
Remove clips securing RH footwell assembly
注4x push clips, Clip count may vary depending on region
-
Remove RH footwell assembly
注2x connectors
-
Remove RH front floormat
-
Remove RH console side panel carpet
注12x clips, 2x locating pins, Use trim tool starting at top edge to release upper clips, Pull bottom to release remaining clips, Use caution and pull panel straight away from console, if panel is peeled off it could be damaged
-
Remove clip securing RH front cabin carpet to body
注1x clip
-
Fold RH front cabin carpet rearward
注Newer Vins may be equipped with additional foam installed below carpet
-
Remove foam plugs to access RH front inner HV battery bolts
注2x plugs, Push pick through foam and turn roughly 45 degrees to grab onto foam insert and pull straight out, Newer vins may be equipped with 1x foam plug
-
Remove both RH front inner HV battery bolts
注2x bolts, EP20, 136 Nm
-
Raise RH front seat cushion to maximum height
注This will allow access to HV battery bolts at RH front foot well and below RH front seat
-
Remove 2nd row floor mat from vehicle
-
Separate carpet perforation below RH front seat to access RH middle inner HV battery bolt
注Located below rear of RH front seat
-
Remove RH middle inner HV battery bolt
注1x bolt, 16mm, 66 Nm
-
Separate carpet perforation below LH front seat to access LH middle inner HV battery bolt
注Located below rear of LH front seat
-
Remove LH middle inner HV battery bolt
注1x bolt, 16mm, 66 Nm
-
Partially remove LH rear door seal
-
Remove LH 7s lower C-pillar trim
注8x clips, Rear edge secures onto trunk side trim, Release front clips then rear clips
-
Fold down 2nd row 60 seatback assembly
注Press button, fold forwards
-
Move 60 seat forward using towel bar
注With one hand on towel bar pull up and slide the seat forward with your other hand
-
Remove 60 seat rear outboard track fastener
注1x patch bolt, 11mm, 37 Nm, Discard after removal
-
Remove 60 seat rear inboard track fasteners
注2x patch bolts, 11mm, 37 Nm, Discard after removal
-
Move 60 seat fully rearward using towel bar
注With one hand on towel bar pull up and slide the seat forward with your other hand
-
Remove 60 seat outboard track cover
注1x clip, Slide covers forward to release from 60 seat tracks
-
Remove center track cover from 2nd row seats
注2x clips, Slide covers forward to release from 2nd row seat tracks
-
Release cabin carpet from 60 seat
注Pull cabin carpet towards front of vehicle
-
Remove 60 seat front inboard track fasteners
注1x bolts, 11mm, 37 Nm, Discard after removal
-
Remove 2nd row 60 seat frame front outboard track fasteners
注1x bolts, 11mm, 37 Nm, Discard after removal
-
Disconnect 2nd row 60 seat connector
注1x connector
-
Remove 2nd row 60 seat assembly from vehicle
注Recommend assistance
-
Partially remove RH rear door seal
注Pillar and sill trim have tabs seated underneath seal
-
Remove RH 7s lower C-pillar trim
注8x clips, Rear edge secures onto trunk side trim, Release front clips then rear clips
-
Remove 40 seat outboard track cover
注1x clip, Slide cover forward to release from 40 seat track
-
Release cabin carpet from 40 seat
注Pull cabin carpet towards front of vehicle
-
Remove bolts securing 40 seat podium to vehicle
注2x patch bolts, 11mm, 37 Nm, Discard bolts after removal
-
Fold 2nd row 40 seat down
-
Move 40 seat forward using towel bar
注With one hand on towel bar pull up and slide the seat forward with your other hand
-
Remove bolts securing 40 seat inner and outer tracks to vehicle
注2x patch bolts, 11mm, 37 Nm, Discard bolts after removal
-
Move 40 seat fully rearward using towel bar
注With one hand on towel bar pull up and slide the seat rearward with your other hand
-
Disconnect 2nd row 40 seat connector
注1x connector
-
Remove 40 seat from vehicle
注Recommend assistance, Do not support 40 seat by cushion pan, Support 40 seat by podium
-
Position object beneath rear cabin carpet to raise and allow access to rear inner HV battery bolts
注Use shop towel or similar
-
Remove RH rear inner HV battery bolt
注1x bolt, 16mm, 66 Nm, Located below RH rear main carpet
-
Remove LH rear inner HV battery bolt
注1x bolt, 16mm, 66 Nm, Located below LH rear main carpet
- Power off the vehicle using the touchscreen.
-
Disconnect the 12V negative battery cable and First Responder Loop.
-
Make a slit in 3rd row carpet around LH seat belt
注Cut a thin straight line on 3rd row carpet from seat belt opening to edge of carpet
-
Make a slit in 3rd row carpet around RH seat belt
注Cut a thin straight line on 3rd row carpet from seat belt opening to edge of carpet
-
Move 3rd row carpet aside
-
Move 3rd row NVH insulation aside
注Use seatbelt or bungee strap as needed
- Empty all pockets and remove all metal objects such as watches and jewelery.
-
Inspect the HV insulating gloves for any damage.
-
Put on the HV insulating gloves and leather over gloves.
-
Remove bolts securing ancillary bay probe lid cover to ancillary bay cover
注2x bolts, EP10 5-Lobe, 6 Nm, Discard after removal
-
Remove ancillary bay probe lid cover from ancillary bay cover
-
Verify no high voltage
注Make sure to wear PPE (HV gloves, safety glasses) when working on high voltage component, Measure B+ to Ground, B- to Ground, B+ to B-, If voltage is greater than 10V, Pack contactors are not open or welded, Stop work and reach out to Service Engineering
-
Inspect ancillary bay probe lid cover gasket then position onto the ancillary bay cover
注Confirm no visual damage present, Replace gasket if damage is found
-
Install the bolts securing ancillary bay probe lid cover to ancillary bay cover
注2x bolts, EP10 5-Lobe, 6 Nm, Install new fasteners
- Remove HV insulating gloves
-
Remove bolt securing busbar cover access door
注1x bolt, 10mm, 9 Nm
-
Remove bolts securing charge port busbar kit to HV header
注2x bolts, 10mm, 9 Nm
-
Lift busbar kit connector to remove from HV header
-
如果充电接口和高压电池之间有一个三相(交流)连接点,请将其断开:
-
Disconnect the HVC logic connector and install logic cap
注1x connector, 1x cap, Release locking tab then push the handle downward to release connector
-
Remove DCDC ground strap from HV battery
注1x nut, 13mm, 15 Nm, Discard after removal
-
Release positive 12V output cover from PCS cable
注1x cover
-
Remove PCS cable from 12V passthrough output
注1x nut, 13mm, 15 Nm, Discard nut after removal
-
Close all four doors
注Latch rear doors to prevent accidental closure
-
Remove wheel chocks and push vehicle onto lift
注Recommend assistance, Note this vehicle can only be safely pushed for a very short distance and at very slow speed, Replace wheel chocks once vehicle in correct position
-
Raise and support vehicle
注Verify jack locations prior to lifting vehicle, ONLY place on lifting points at front and rear of rocker panels
- Fully raise the vehicle, and then lower the lift onto the locks.
-
Remove the outer fasteners from the front aero shield.
-
Remove the remaining nuts (x2), and then remove the front aero shield from the vehicle.
-
Release RH front wheel liner from HV battery and lower wheel well area
注3x clips, 1x bolt, 10mm, 5 Nm
-
Release LH front wheel liner from HV battery and lower wheel well area
注3x clips, 1x bolt, 10mm, 5 Nm
-
Remove bolts securing front skid plate
注4x bolts, E10, 13 Nm
-
Remove skid plate from HV battery
-
Disconnect both AC compressor and PTC heater HV harness connectors on HV battery
注2x locking connectors, 2 stage locking connectors, Disengage the red locking tab by pulling it away from the connector, then depress the green tab to release
-
Secure LH front wheel liner away from HV battery
-
Secure RH front wheel liner away from HV battery
-
Position coolant drain container underneath RH front of HV battery
-
Disconnect PT return hose at RH side of vehicle and plug female side of hose
注1x spring clip, 1x hose clip, 1x plug
-
Disconnect rear PT supply hose at RH side of vehicle and plug male side of hose
注1x spring clip, 1x hose clip, 1x plug
-
Position coolant drain container underneath LH front of HV battery
-
Disconnect HV battery return hose at LH side of vehicle and plug male side of hose
注1x spring clip, 1x plug
-
Position coolant drain container below HV battery manifold hose
-
Remove HV battery front manifold hose clips from body
注2x clips, Newer vehicles may be equipped with 1x clip
-
Disconnect HV battery front manifold hose and plug both hose ends
注1x spring clip, 2x plugs
-
Remove coolant drain container from underneath vehicle
-
Remove mid aero shield
注11x bolts, 10mm, 5 Nm, Fasteners may vary, MYSP will have one less bolt and an extra clip
-
Position support stand to support front portion of rear subframe
-
Release clips securing coolant hoses to LH shear plate
注2x fir tree clips
-
Remove smaller fasteners for LH shear plate
注2x bolts, 13mm, 35 Nm
-
Remove large bolt securing LH shear plate and subframe to body and remove shear plate
注1x bolt, 21mm, 130 Nm, Discard at later step
-
Hand tighten bolt securing LH side of subframe to body
注1x bolt, 21mm, 130 Nm
-
Release clips securing coolant hoses to RH shear plate
注2x fir tree clips
-
Remove smaller fasteners for RH shear plate
注2x bolts, 13mm, 35 Nm
-
Remove large bolt securing RH shear plate and subframe to body and remove shear plate
注1x bolt, 21mm, 130 Nm, Discard at later step
-
Hand tighten bolt securing RH side of subframe to body
注1x bolt, 21mm, 130 Nm
-
Remove support stand from under vehicle
-
Release LH side hose clip from rear battery skid plate
注2x clips, Clip quantity may vary on older vehicles
-
Release RH side hose clips from rear battery skid plate
注2x fir tree clips
-
Remove lower bolts securing rear battery enclosure skid plate
注2x bolts, EP10, 13 Nm
-
Remove upper nut securing rear battery enclosure skid plate
注1x nut, 10mm, 13 Nm
-
Remove upper bolts securing rear battery enclosure skid plate from HV battery
注4x bolts, 13mm, 35 Nm
-
Remove rear battery enclosure skid plate from HV battery pack
-
Position coolant drain container underneath LH rear of HV battery
-
Disconnect RDU inverter inlet hose from rear of HV battery and plug both ends
注1x spring clip, 2x plugs
-
Position coolant drain underneath RH rear of HV battery
-
Remove nut securing RDU HV cable bracket to HV battery
注1x nut, 10mm, 10 Nm
-
Disconnect RDU HV cable from HV battery
注1x connector, Release locking tab and rotate the release lever up to disengage the connector, Do not force the release lever up, Ensure the alignment tabs on the RDU header are not damaged
-
Place battery table into position and lower vehicle to support battery
注Recommend assistance, Line up table so center 4 bolts are accessible through opening in table, Adjust final battery table position using adjustable caster jacks on table
-
Remove central bolts securing HV battery through center ski cover
注4x bolts, EP14, 34 Nm
-
Remove bolts securing LH front support bracket to vehicle
注4x bolts, 16mm, 110 Nm
-
Remove bolts securing RH front support bracket to vehicle
注4x bolts, 16mm, 110 Nm
-
Remove LH bolts securing HV battery to vehicle
注8x bolts, 13mm, 35 Nm
-
Remove RH bolts securing HV battery to vehicle
注8x bolts, 13mm, 35 Nm
-
Raise vehicle to free from HV battery
注Recommend assistance
-
Remove battery from under vehicle
注Recommend assistance
-
Remove ancillary bay perimeter seal from HV battery pack
注Discard after removal
安装
-
Install ancillary bay perimeter seal to HV battery pack
注Install new perimeter seal every time the HV battery is removed and reinstalled
-
Install HV battery alignment rods
注2x rods, Located on body at front of vehicle, 2x rods, Located at rear of HV battery near ancillary bay
-
Lower vehicle onto HV battery and align holes
注Recommend assistance, Use alignment rods, Be sure coolant hoses do not get caught on alignment rods, Caution not to damage HV cable, Do not fully lower vehicle onto battery (this will help with installing battery bolts)
-
Install bolts securing HV battery to body at LH shear plate area hand tight
注2x bolts, 13mm, 35 Nm, Torque at later step
-
Install bolts securing HV battery to body at RH shear plate area hand tight
注2x bolts, 13mm, 35 Nm, Torque at later step
-
Loosely install RH bolts securing HV battery to vehicle hand tight
注8x bolts, 13mm, 35 Nm
-
Loosely install LH bolts securing HV battery to vehicle hand tight
注8x bolts, 13mm, 35 Nm
-
Remove HV battery front alignment rods
注2x rods
-
Install bolts securing RH front support bracket to vehicle hand tight
注4x bolts, 16mm, 110 Nm, Torque at later step
-
Install bolts securing LH front support bracket to vehicle hand tight
注4x bolts, 16mm, 110 Nm, Torque at later step
-
Install central bolts securing HV battery through center ski cover hand tight
注4x bolts, EP14, 34 Nm, Torque at later step
-
Open LH rear door
注Use caution while working around this area not to damage any components
-
Remove HV battery alignment rod from LH rear inner bolt location
注1x rod
-
Install LH rear inner HV battery bolt hand tight
注1x bolt, 16mm, 66 Nm, Lift up LH rear main carpet for access, Torque at later step
-
Install LH middle inner HV battery bolt hand tight
注1x bolt, 16mm, 66 Nm, Torque at later step
-
Close LH rear door
注Do not latch
-
Open LH front door
注Use caution while working around this area not to damage any components
-
Install both LH front inner HV battery bolts hand tight
注2x bolts, EP20, 136 Nm, Torque at later step
-
Close LH front door
注Do not latch
-
Open RH rear door
注Use caution while working around this area not to damage any components
-
Remove HV battery alignment rod from RH rear inner bolt location
注1x rod
-
Install RH rear inner battery bolt hand tight
注1x bolt, 16mm, 66 Nm, Lift up LH rear main carpet for access, Torque at later step
-
Install RH inner HV battery bolt hand tight
注1x bolt, 16mm, 66 Nm, Torque at later step
- Close RH rear door
-
Open RH front door
注Use caution while working around this area not to damage any components
-
Install both RH front inner HV battery bolts hand tight
注2x bolts, EP20, 136 Nm, Torque at later step
-
Close RH front door
注Do not latch
-
Lower vehicle onto pack completely
注Recommend assistance
-
Torque RH bolts securing HV battery to vehicle
注8x bolts, 13mm, 35 Nm
-
Torque LH bolts securing HV battery to vehicle
注8x bolts, 13mm, 35 Nm
-
Torque bolts securing RH front support bracket to vehicle
注4x bolts, 16mm, 110 Nm
-
Torque bolts securing LH front support bracket to vehicle
注4x bolts, 16mm, 110 Nm
-
Torque central bolts securing HV battery through center ski cover
注4x bolts, EP14, 34 Nm
-
Raise vehicle and lower onto locks, then remove battery table from under vehicle
注Recommend assistance, Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
-
Position support stand to support front section of rear subframe
-
Install bolt and shear plate to LH side of rear subframe hand tight
注1x bolt, 21mm, 130 Nm, Torque at later step
-
Install bolts securing LH rear shear plate to body hand tight
注2x bolts, 13mm, 35 Nm, Torque at later step
-
Torque bolt securing subframe and LH rear shear plate to body
注1x bolt, 21mm, 130 Nm, Mark bolt after torque
-
Torque small fasteners securing LR rear shear plate to body
注2x bolts, 13mm, 35 Nm
-
Install bolt and shear plate to RH side of rear subframe hand tight
注1x bolt, 21mm, 130 Nm, Torque at later step
-
Install bolts securing RH shear plate to HV battery hand tight
注2x bolts, 13mm, 35 Nm, Torque at later step
-
Torque bolt securing subframe and RH rear shear plate to body
注1x bolt, 21mm, 130 Nm
-
Torque small fasteners securing RH rear shear plate to body
注2x bolts, 13mm, 35 Nm
-
Remove support stand from under vehicle
-
Install clips securing coolant hoses to RH shear plate
注2x fir tree clips
-
Install clips securing coolant hoses to LH shear plate
注2x fir tree clips
-
Connect RDU HV cable to HV battery
注1x connector, Make sure the connector lock is 90 degrees from the connector before beginning to secure the connector, Use one hand to support the connector while other latching locking tab. Once installed, verify that the latch is not damaged and fully secured in the latched position
-
Install nut securing RDU HV cable bracket to HV battery
注1x nut, 10mm, 10 Nm
-
Position coolant drain underneath RH rear of HV battery
-
Remove hose plugs and connect coolant outlet hose to rear PT return hose
注1x spring clip, Perform push-pull-push test to make sure hose is fully seated, Use shop towel to clean any coolant residue if necessary.Loss of coolant greater than 1L requires coolant vacuum fill
-
Position coolant drain container underneath LH rear of HV battery
-
Remove plugs and connect RDU inverter inlet hose to rear of HV battery
注1x spring clip, Perform push-pull-push test to make sure hose is fully seated,Loss of coolant greater than 1L requires coolant vacuum fill
-
Remove coolant drain container from underneath vehicle
-
Position rear battery enclosure skid plate to HV battery for installation
-
Install upper bolts securing rear battery enclosure skid plate to HV battery hand tight
注4x bolts, 13mm, 35 Nm, Torque at later step
-
Install upper nut securing rear battery enclosure skid plate hand tight
注1x nut, 10mm, 13 Nm, Torque at later step
-
Install lower bolts securing HV battery rear skid plate enclosure
注2x bolts, EP10, 13 Nm, Torque at later step, Earlier vins may be equipped with additional bolts
-
Torque bolts securing HV battery and rear skid plate to vehicle
注4x bolts, 13mm, 35 Nm
-
Torque upper nut securing rear battery enclosure skid plate
注1x nut, 10mm, 13 Nm
-
Install lower bolts securing HV battery rear skid plate enclosure
注2x bolts, EP10, 13 Nm, Torque at later step, Earlier vins may be equipped with additional bolts
-
Install RH side hose clips to rear battery skid plate
注2x fir tree clips
-
Install LH side hose clip to HV battery rear skid plate enclosure
注2x clips, Clip quantity may vary on older vehicles
-
Apply Loctite 222 onto mid aero shield bolts and install mid aero shield
注11x bolts, 10mm, 5 Nm, Fasteners may vary, Model Y Structural Pack has one less bolt and one extra clip
-
Position coolant drain container underneath LH front of HV battery
-
Remove plugs then connect HV battery coolant return hose
注1x spring clip,1x plug
-
Position coolant drain container below HV battery manifold hose
-
Remove plugs then connect HV battery front manifold coolant hose
注1x spring clip, 2x plugs, Perform push-pull-push test to make sure hose is fully seated.Loss of coolant greater than 1L requires coolant vacuum fill
-
Install HV battery front manifold hose clips to body
注2x clips, Newer vehicles may be equipped with 1x clip
-
Position coolant drain container underneath RH front of HV battery
-
Remove plugs then connect PT supply hose
注1x spring clip, 1x hose clip, 2x plugs, Perform push-pull-push test to make sure hose is fully seated.Loss of coolant greater than 1L requires coolant vacuum fill
-
Remove plugs and connect PT return hose
注1x spring clip, 1x hose clip, 2x plugs, Perform push-pull-push test to make sure hose is fully seated.Loss of coolant greater than 1L requires coolant vacuum fill
-
Remove coolant drain container from underneath vehicle
-
Connect both AC compressor and PTC heater HV harness connectors on HV battery
注2x locking connectors, 2 stage locking connector, After the connector is seated and there is an audible click, Engage the second lock by pressing towards the connector
-
Install FDU ground strap and bolt to HV battery
注1x bolt, 10mm, 10 Nm
-
Install FDU HV harness connector onto FDU
注1x connector, Ensure the connector is installed far enough on the FDU manifold so the manifold alignment tooth is making contact with the connector lever
-
Connect FDU HV harness connector and lock release lever
注1x connector, Apply slight pressure to the connector as the lever is rotated into position, Move the lever to the closed position slowly and ensure the lever teeth and manifold teeth are properly meshed, There should be a very small gap between the manifold and the connector when fully seated
-
Install bolt securing FDU HV harness to FDU
注1x bolt, EP10, 10 Nm
-
Install front skid plate onto HV battery
注2x tabs, Slide tabs onto front of HV battery
-
Install the bolts securing the front skid plate to the HV battery
注4x bolts, E10, 13 Nm
-
Release LH front wheel liner from bungee strap
注Remove strap from vehicle
-
Install LH front wheel liner to HV battery and lower wheel well area
注3x clips, 1x bolt, 10mm, 5 Nm
-
Release RH front wheel liner from bungee strap
注Remove strap from vehicle
-
Install RH front wheel liner to HV battery and lower wheel well area
注3x clips, 1x bolt, 10mm, 5 Nm
-
Position the front aero shield on the vehicle, and then install the nuts that attach the aero shield to the vehicle.
-
Apply Loctite 222 on the front aero shield bolts, and then install the bolts on the aero shield.
-
Lower vehicle fully and move rack arms away from vehicle
注Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
-
Push vehicle away from lift
注Recommend assistance, Place wheel chocks to keep vehicle from moving, Note this vehicle can only be safely pushed for a very short distance and at very slow speed
-
Open all four doors
注Latch rear doors to prevent accidental closure
-
Install positive 12V output
注1x nut, 13mm, 9 Nm, Install new nut, Make sure rubber boot is not pinched between cable terminal and pass through
-
Install positive 12V output cover to PCS cable
注1x cover
-
Install nut securing DCDC ground strap to HV battery
注1x nut, 13mm, 15 Nm, Install new nut
-
Remove logic cap and connect the HVC logic connector
注1x connector, 1x cap, Align connector then pull the handle to locking position get connector fully seated
-
Clean busbar HV connector contact surface of residual Penetrox
注Allow 1 minute dry time after removing Penetrox, It is necessary to clean HV connector during re-use of busbar
-
Clean HV connector contact surface of residual Penetrox
注Allow 1 minute dry time after removing Penetrox, New busbar comes with Penetrox applied to HV connector
-
Apply Penetrox onto HV connector joints
注Apply 2 drops of Penetrox A-13 about 5mm in diameter to either side of the hole on both leads, Spread evenly to verify the contact surface is fully covered
-
Position busbar kit connector and lower onto HV header
-
Install bolts securing charge port busbar kit to HV Header
注2x bolts, 10mm, 9 Nm
-
Inspect HV insulating gloves
注Check gloves for damage prior to use, Refer to service document TN-15-92-003 R1, for information on inspecting HV gloves. https://service.teslamotors.com/protected-doc/ServiceBulletins/External/TN/TN-15-92-003_High_Voltage_Awareness_Care_Points_R4.pdf
-
Put on HV insulating gloves and leather over gloves
注Make sure to wear Electrical Protective Gloves any time Hioki tester is used
-
Perform Hioki resistance test at each HV joint from HV busbar lead to bolt head
注2x HV joints, The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ).If the resistance is greater than 0.195 mΩ (195 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again.If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again.If the resistance is repeatedly between 0.00 mΩ and 0.050 mΩ (50 μΩ), hioki test passed, proceed to next step
- Remove HV insulating gloves
-
Install fastener securing busbar cover access door
注1x bolt, 10mm, 9 Nm
-
如果充电接口和高压电池之间有一个三相(交流)连接点,请将其连接:
-
Move 3rd row NVH insulation back into position
-
Move 3rd row carpet back into position
-
Install 2nd row 60 seat assembly
注Recommend assistance
-
Connect 2nd row 60 seat connector
注1x connector
-
Install fasteners securing 60 seat frame to body
注5x patch bolts, 11mm, 37 Nm, Install new patch bolts, Bottom seat bolts located behind main carpet, Torque in sequence; Outboard front -> Both inboard rear -> Outboard rear -> Inboard front
-
Install 40 seat into vehicle
注Recommend assistance, Do not support 40 seat by cushion pan, Support 40 seat by podium
-
Connect 2nd row 40 seat connector
注1x connector
-
Install bolts securing 40 seat podium to vehicle hand tight
注2x patch bolts, 11mm, 37 Nm, Install new bolts, Torque at later step
-
Move 40 seat forward using towel bar
注With one hand on towel bar pull up and slide the seat forward with your other hand
-
Install bolts securing 40 seat inner and outer tracks to vehicle
注2x patch bolts, 11mm, 37 Nm, Install new bolts
-
Move 40 seat to original position
-
Torque bolts securing 40 seat podium to vehicle
注2x patch bolts, 11mm, 37 Nm
-
Secure cabin carpet to 60 seat
注Strap velcro on
-
Install cabin carpet to 40 seat
-
Install 60 seat outboard track cover
注1x clip
-
Install center track cover to 2nd row seats
注2x clip, Slide cover straight on to clip to 2nd row seat tracks
-
Install 40 seat outboard track cover
注1x clip
-
Install RH 7s lower C-pillar trim
注8x clips, Rear edge is secures onto trunk side trim, Secure rear clips then front clips
-
Reseat RH rear door seal
注Seat pillar and sill trim tabs underneath seal
-
Install LH 7s lower C-pillar trim
注8x clips, Rear edge is secures onto trunk side trim, Secure rear clips then front clips
-
Reseat LH rear door seal
注Seat pillar and sill trim tabs underneath seal
-
Torque LH rear inner HV battery bolt
注1x bolt, 16mm, 66 Nm, Located below LH rear main carpet
-
Torque RH rear inner battery bolt
注1x bolt, 16mm, 66 Nm, Located below RH rear main carpet for access
-
Torque LH middle inner HV battery bolt
注1x bolt, 16mm, 66 Nm
-
Fold LH side of rear main carpet to its original position
-
Torque RH middle inner HV battery bolt
注1x bolt, 16mm, 66 Nm
-
Fold RH side of rear main carpet to its original position
-
Install 2nd row floor mat into vehicle
-
Torque both RH forward HV battery bolts
注2x bolts, EP20, 136 Nm
-
Install RH front cabin carpet support access plugs
注2x plugs, Newer Vins may be equipped with 1x foam plug
-
Fold the RH front main cabin carpet back to original position
-
Install clip securing RH front cabin carpet to body
注1x clip
-
Install clip securing RH lower A-pillar trim
注1x clip
-
Install RH mid A-pillar assembly
注1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Make sure the seal seat on top of the trim
-
Install RH console side panel carpet
注12x clips, 2x locating pins, Position side panel and align the front locator, then the rear locator, Push side panel towards console to install
-
Install RH front floor mat
-
Position RH footwell assembly
注2x connectors
-
Install clips securing RH footwell assembly
注4x push clips, 2x connectors, Puddle lamp and speaker
-
Torque both LH front inner HV battery bolts
注2x bolts, EP20, 136 Nm
-
Install LH front cabin carpet support access plugs
注2x plugs, Newer vins may be equipped with 1x foam plug
-
Fold the LH front main cabin carpet back to original position
-
Install LH console side panel carpet
注11x clips, 2x locating pins, Position side panel and align the front into front locator, then the rear locator, Push side panel towards console to install
-
Install LH front floor mat
注2x velcro patches, Ensure mat does not interfere with pedal operation
-
Install LH footwell cover
注3x tabs, 1x Ethernet connector, 1x puddle light connector
-
Install screw and clips securing LH footwell cover
注1x screw, T20, 2.5 Nm, 2x push clips
-
Install LH lower A-pillar trim
注6x clips, 2 locating pins, Align front locating pin first
-
Install clip securing LH lower A-pillar trim
注1x push clip
-
Install LH mid A-pillar assembly
注1x clip, 1x tab, Align the bottom tab then push the top clip to fully seat mid A-pillar, Pull seal over trim
-
Remove coolant bottle cap
-
Place empty coolant container into front storage area
-
Fill container with at least 15L of coolant
-
Place filled coolant container into front storage area
-
Close air inlet and coolant refill valves
-
Install refill tool cap onto coolant bottle assembly
-
Setup vacuum refill tool
注Verify all valves on refill tool are in the closed position, See image for clarity
-
Install vacuum refill hose into refill cap on coolant bottle
注Perform push-pull-push test to verify hose is fully installed
-
Place end of overflow hose into empty container
-
Connect shop air supply to coolant refill tool
注If not already done, Verify refill valve is set to off
-
Open air inlet valve to draw a vacuum, Once gauge stabilizes, Fully close valve
注Gauge stabilizes roughly (60-70 cmHg), Vacuum should not drop after the valves are closed
-
Slowly open refill valve to allow coolant to be drawn into system
注Make sure hose end of refill hose is fully submerged during entire process
-
Once gauge reads zero, close refill valve
-
Slowly open the coolant refill valve to allow coolant to be drawn into the system
注Make sure end of coolant refill hose is fully submerged during entire process
-
Monitor gauge for 30 seconds to verify a vacuum is maintained in the cooling system
-
Reopen the air inlet valve for 3 minutes to continue evacuating cooling system, then close valve
-
Disconnect shop air supply from coolant refill tool
-
Remove coolant refill hose from coolant container
-
Remove coolant overflow hose from coolant container
-
Remove vacuum refill hose from refill cap on coolant bottle
-
Remove coolant refill tool from vehicle
-
Remove both coolant containers from inside underhood area
-
Connect the First Responder Loop and 12V negative battery cable.
-
Press and hold park button to release EPB service mode
注Remove wheel chocks if necessary
-
Connect to vehicle using Toolbox 3.0
注Vehicle connection is integrated into drivers footwell cover, Open Toolbox 3 website and establish connection to the vehicle. https://toolbox.teslamotors.com, Select connection status icon at top right corner, and select connect locally (icon will turn green when vehicle is connected)If RJ45 ethernet diagnostic connector present connect directly from laptop using an RJ45 Ethernet cable
- Select ‘Actions/Autodiag’ tab and search for ‘ Purge'
-
Select ‘TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGESearch for routine in ToolboxCoolant Air PurgeThermal / Coolant System - Coolant Purge Starthv / Front Drive Inverter Replacement - Coolant Air Purgehv / Rear Drive Inverter Replacement - Coolant Air Purgehv / Rear Left Drive Inverter Replacement - Coolant Air Purgehv / Rear Right Drive Inverter Replacement - Coolant Air Purgehv / Front Drive Unit Replacement - Coolant Air Purgehv / Rear Drive Unit Replacement - Coolant Air PurgeThermal / Actions - Coolant Purge Stop or Coolant Purge Start ’, click ‘Run’, and allow routine to complete
注Make sure vehicle is not in drive state, Plan is still running despite the stop message, Coolant pumps will be audible, Test lasts approximately 10 mins, Speeds can be monitored in garage under PT Thermal tab, Idle speed = ~1500 RPM, Test will vary speeds from 3500-6500 RPM and actuate valve between SERIES and PARALLEL, Putting vehicle into drive state will stop this routine, If speeds hover at 7000 RPM, that means the pumps are air locked, perform vacuum fill again, Continue to add coolant and purge until the coolant level reaches between the NOM and MAX Lines on the bottle, Select ‘X’ at top right of window to close once complete
-
Inspect coolant level and top off as necessary
注Ensure coolant is filled using G-48 coolant
-
Install coolant bottle cap
-
Select ‘TEST-SELF_VCFRONT_X_HEAT-PUMP-THERMAL-PERFORMANCESearch for routine in ToolboxHeat Pump Thermal System Performance Test’, click ‘Run’, and allow routine to complete
注Select ‘X’ at top right of window to close once complete.
- Disconnect the laptop from the vehicle.
-
Install the rear apron.
- Close the hood.
- Raise all four windows
-
Remove lift pad adapters from RH rocker
注2x lift pad adapters
-
Install butyl patches onto RH rocker access holes
注2x butyl patches, Apply pressure along patch to verify fully secured to body, Replace with new patch if needed, Roughly 2" x 2 1/2"
-
Close all four doors
注If 12V is powered up, Unlatch rear doors before closing
-
Install RH rocker carrier onto body
注10x clips
-
Install bolts securing RH rocker carrier to body
注2x bolts, 10mm, 5 Nm
-
Install RH rocker panel onto RH rocker carrier
注11x clips, 11x tabs, Recommend assistance, Tabs go into cavities on the rocker carrier and cannot be accessed from outer side of trim
-
Install clips securing RH rocker cover to front and rear wheel liner
注4x push clips
-
Remove lift pad adapters from LH rocker
注2x lift pad adapters
-
Install butyl patches onto LH rocker access holes
注2x butyl patches, Apply pressure along patch to verify fully secured to body, Replace with new patch if needed, Roughly 2" x 2 1/2"
-
Install LH rocker carrier onto body
注10x clips
-
Install bolts securing LH rocker carrier to body
注2x bolts, 10mm, 5 Nm
-
Install LH rocker panel onto LH rocker carrier
注11x clips, 11x tabs, Recommend assistance, Tabs go into cavities on the rocker carrier and cannot be accessed from outer side of trim
-
Install clips securing LH rocker cover to front and rear wheel liner
注4x push clips