2026-11-02

高压电池 (RWD)（拆卸和安装）

校正代码 16010101 3.72 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时，深入了解 FRT 及其创建方式。 注意：请参阅人员保护，确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。注意：请参阅人体工程学注意事项查看安全健康的作业规程。

  • 2026-11-02: Added the removal and installation steps for the 2nd row 60 seats and updates the Vehicle HV Disablement Procedure.
  • 2025-10-10: Changed procedure sequence for cleaning the HV busbar and HV header connector contact surfaces.
  • 2025-01-08: Added images of HV battery alignment rods for clarification.
  • 2024-11-07: Added 3-phase harness disconnect/connect steps.
  • 2024-06-13: Updated lift pad adapter PNs.
  • 2023-11-21: Added new lift pad instructions.
  • 2023-11-02: Added a note to remind of double-checking the charge port busbar connector before removing the HV battery to avoid damage, and added a pain-point video in the same step.
  • 2023-08-23: Updated EPB Service Mode reference.
  • 2023-05-22: Added caution for correct positive DC cable connection.
Equipment:
  • 1936724-00-A - 通用举升机垫适配器
  • 1133787-00-A 安全带释放按键，Model 3
  • 1020566-00-F ASY, Battery Table, Manual Lift
  • 1020566-99-A 电池操作台手动升降机顶板
  • 1129166-00-A Hoist, H-Frame EMEA
  • 1134523-00-A 电池校准杆套件，Model 3
  • 1140311-00-A Lever Lock, HV Connector, Model 3
  • 1053600-00-B 驱动单元压力测试固定装置
  • 1130942-00-B 冷却液储液罐压力测试适配器
  • 1132185-00-B 冷却液泄漏测试适配器套件，Model 3
  • 1133843-00-A 冷却液排放和加注适配器套件，M3
  • 1135762-00-A 冷却软管维修堵头套件，Model 3
  • GSN-TL-000564 电池冷却液排放和加注套件
  • 1026636-00-A Pack Enclosure Leak Tester, HV Battery
  • 1140501-00-A Pack Kit, Enclosure, Leak Test, HV Battery, Complete
  • 1144879-00-A Kit, Encl Leak Test Adapters, HV Battery
  • 1108272-00-B 变流器逻辑连接器盖，3DU
Warning
If installing the HV battery after the vehicle has been in a collision, do not reuse HV battery mounting bolts. Use only new HV battery mounting bolts when reinstalling the HV battery.

扭矩规格

Table 1. 扭矩规格: 高压电池 (RWD)（拆卸和安装）
描述 扭矩值 推荐工具 重复使用/更换 备注
LH front inner HV battery bolt
136 Nm (100.3 lbs-ft)
  • 梅花 Plus EP20 套筒
重复使用
LH middle inner HV battery bolt
66 Nm (48.7 lbs-ft)
  • 16 毫米套筒
重复使用
LH rear inner HV battery bolt
66 Nm (48.7 lbs-ft)
  • 16 毫米套筒
重复使用
Bolts that secure the 2nd row 60 seat frame to the body
37 Nm (27.3 lbs-ft)
  • 11 mm socket
  • Cordless 3/8in Dr Impact
  • 6 in extension
更换 1616775-00-B
Bolt that secures the busbar cover access door
9 Nm (6.6 lbs-ft)
  • 10 毫米深套筒
重复使用
Bolts that attach the charge port busbar kit to the HV header
9 Nm (6.6 lbs-ft)
  • 10 毫米深套筒
重复使用
Nut that attaches the DCDC ground strap to the HV battery
9 Nm (6.6 lbs-ft)
  • 13 毫米 12 角深套筒
更换 1093060-00-A
Nut that attaches the positive 12V output to the PCS cable
9 Nm (6.6 lbs-ft)
  • 13 mm 套筒
更换 1093060-00-A
Bolt that attaches the LH front wheel liner to the HV battery
5 Nm (3.7 lbs-ft)
  • 10 毫米套筒扳手
重复使用
Smaller bolts that attach the LH shear plate to the body
35 Nm (25.8 lbs-ft)
  • 13 mm 套筒
重复使用
Larger bolt that attaches the LH shear plate to the body
130 Nm (95.9 lbs-ft)
  • 21 毫米套筒
更换 1461657-00-A
Nut that attaches the RDU HV electrical harness bracket to the HV battery
10 Nm (7.4 lbs-ft)
  • 10 毫米套筒扳手
重复使用
Center bolts (x4) that attach the HV battery through the HV battery center rail ski cover
35 Nm (25.8 lbs-ft)
  • 外梅花套筒 Plus EP14
重复使用
Outer bolts (x2) that attach the center rail ski cover to the HV battery
32 Nm (23.6 lbs-ft)
  • 外梅花套筒 Plus EP14
重复使用
Bolts that attach the HV battery LH and RH support brackets to the vehicle
110 Nm (81.1 lbs-ft)
  • 16 毫米套筒
重复使用
Bolts (x16) that attach the HV battery to the vehicle
35 Nm (25.8 lbs-ft)
  • 13 mm 套筒
重复使用

拆卸

  1. Remove the LH lower rocker panel cover. See 盖板 - 门槛板 - 下 - 左侧（拆卸和更换）.
  2. Remove the LH rocker panel carrier. See 支架 - 门槛板 - 左侧（拆卸和更换）.
  3. Remove the butyl patches that cover the LH rocker access hole.
  4. Repeat step 1 through step 3 for the RH side of the vehicle.
  5. 安装举升垫适配器。
    • 仅适用于欧洲、中东和非洲：安装举升机垫适配器，Model Y (1614078-00-A)
    • 其他地区：安装通用举升垫适配器 (1936724-00-A)。
    Warning
    请勿使用任何其他举升垫适配器。
    Note
    欧洲、中东和非洲以外地区：使用通用举升垫适配器 (1936724-00-A) 代替 举升机垫适配器，Model Y (1614078-00-A)。请弃用任何其他版本的举升垫适配器。
    Note
    通用举升垫适配器在欧洲、中东和非洲尚不可用。请确保在 Model Y 上使用 Model Y 橡胶举升垫，在 Model 3 上使用 Model 3 举升垫。

    通用举升垫适配器说明：

    1. 将与举升机类型相匹配的正确螺纹适配器安装到举升机适配器上。
    2. 确保将螺纹止动垫圈正确安装并紧固至举升机适配器底部。如果未安装螺纹止动垫圈，请勿继续使用举升机适配器。
    3. 将举升机适配器安装到举升臂上，使黑色的举升垫朝向车辆。
      Warning
      确保适配器安装方向正确。
    4. 调整举升臂位置，使举升机适配器与车辆上的固定销孔对齐。
    5. 抬起举升臂，将举升垫完全放置到车辆上。
    6. 确保所有 4 个适配器均已完全就位在车辆上。
  6. Enable Service Mode. See 维护模式.
  7. Unlock the vehicle gateway. See 网关（解锁）.
  8. On the touchscreen, touch Thermal > Coolant System > Coolant Fill/Drain, then touch Run and close once the routine is completed.
    Note
    Thermal Fill Drain routine has a 5 hour time limit. After 5 hours, the routine must be performed again.
  9. Open all the doors and lower all the windows.
  10. Remove the rear underhood apron. See 前备箱挡板 - 后部（拆卸和更换）.
  11. Remove the HEPA filter assembly. See 总成 - 过滤器 - HEPA 空调滤清器（拆卸和更换）.
  12. Remove the LH instrument panel end cap. See 端盖 - 仪表板 - 左侧（拆卸和更换）.
  13. Remove the LH middle A-pillar trim. See 饰板 - A 柱 - 中部 - 左侧（拆卸和更换）.
  14. Remove the LH lower A-pillar trim. See 饰板 - A 柱 - 下 - 左侧（拆卸和更换）.
  15. Move the driver seat fully rearwards.
  16. Remove the driver footwell cover. See 盖板 - 脚部空间 - 驾驶位（拆卸和更换）.
  17. Remove the LH center console side panel carpet. See 侧板 - 中控台 - 左侧（拆卸和更换）.
  18. Remove the clip that attaches the LH front carpet to the vehicle, and then fold the carpet rearward.
  19. Remove the foam plugs in the padding underneath LH front carpet, and then remove the LH front inner HV battery bolts (x2).
    Tip
    推荐使用以下工具
    • 梅花 Plus EP20 套筒
  20. Raise the LH front seat fully.
  21. Repeat step 10 through step 18 for the RH side of the vehicle.
  22. Remove the 2nd row floor mat from the vehicle.
  23. Lift the flap in the carpet underneath the RH front seat, and then remove the RH middle inner HV battery bolt that attaches the HV battery to the vehicle. Repeat this step for the LH side of the vehicle.
    Tip
    推荐使用以下工具
    • 16 毫米套筒
  24. Remove the 2nd row lower seat cushion. See 座椅座垫 - 下部 - 第二排（拆卸和更换）.
  25. Remove the LH lower C-pillar trim. See 饰板 - C 柱 - 下 - 左侧（拆卸和更换）.
  26. Remove the clip securing the LH lower B-pillar to body.
  27. Repeat steps 23 and 24 for the RH side of the vehicle.
  28. Remove the clips (x3) that attach the rear carpet to the vehicle.
  29. Position a folded shop towel underneath the rear cabin carpet to raise the carpet and allow access to the rear inner HV battery bolts, and then remove the LH and RH bolts.
    Tip
    推荐使用以下工具
    • 16 毫米套筒
  30. Disconnect 12V power. See 12V/低压电源（断开和连接）.
  31. 执行车辆高压禁用程序。请参阅 车辆高压禁用程序。
  32. Disconnect the 2nd row 40 seat connector.
    Note
    There may be a red locking tab on newer models.
  33. Remove and discard the bolts (x5) that attach the 2nd row 60 seat frame to the body.
    Note
    Bottom seat bolts are located behind the main carpet.
    Note
    Use of the following tool(s) is recommended:
    • 11 mm socket
    • Cordless 3/8in Dr Impact
    • 6 in extension
  34. Fold the 2nd row 60 seat back downward.
    Note
    Protect the seat back upholstery if necessary. Do not put weight on seat in folded position without cushion present due to risk of bending locator tab on frame.
  35. Disengage the locking tab and disconnect the 2nd row 60 seat connector.
  36. Release the 2nd row 60 seat connector from the LH seat frame.
    Note
    Pinch tabs on clip to avoid damage.
  37. Remove the 2nd row 60 seat assembly from the vehicle.
    Note
    Recommend assistance. If the seat that is not being replaced does not have the ISOFIX flag for child locks, the seat cover will also require replacement.
  38. Disconnect the logic electrical connector at the LH seat frame.
  39. Release the clip that attaches the logic electrical harness to the LH seat frame.
  40. Remove the bolt that secures the busbar cover access door.
    Tip
    推荐使用以下工具
    • 10 毫米深套筒
  41. Remove the bolts that attach the charge port busbar kit to the HV header, and then lift to remove the kit from the header.
    Tip
    推荐使用以下工具
    • 10 毫米深套筒
  42. 如果充电接口和高压电池之间有一个三相（交流）连接点，请将其断开：
    1. 滑动释放装置，将充电接口至高压电池线束的三相连接器把手从固定位置解锁。
    2. 将三相连接器把手抬至最高处。
    3. 将三相连接器从高压电池仓三相接头上拆下。
  43. Disconnect the HVC logic connector, and then install the logic cap.
  44. Remove and discard the nut that attaches the DCDC ground strap to the HV battery, and then remove the strap from the battery.
    Tip
    推荐使用以下工具
    • 13 毫米 12 角深套筒
  45. Release the positive 12V output cover from the PCS cable, remove and discard the nut that attaches the positive 12V output to the PCS cable, and then move the cable aside.
    Tip
    推荐使用以下工具
    • 13 mm 套筒
  46. Close all doors.
    Note
    Doors will be unlatched at a later step.
  47. Remove the wheel chocks from the wheel.
  48. With assistance, push the vehicle onto the lift, then re-chock the wheels when the vehicle is in position.
    CAUTION
    Only push the vehicle for a very short distance and at less than 1 MPH.
  49. 安装举升垫适配器。
    • 仅适用于欧洲、中东和非洲：安装举升机垫适配器，Model Y (1614078-00-A)
    • 其他地区：安装通用举升垫适配器 (1936724-00-A)。
    Warning
    请勿使用任何其他举升垫适配器。
    Note
    欧洲、中东和非洲以外地区：使用通用举升垫适配器 (1936724-00-A) 代替 举升机垫适配器，Model Y (1614078-00-A)。请弃用任何其他版本的举升垫适配器。
    Note
    通用举升垫适配器在欧洲、中东和非洲尚不可用。请确保在 Model Y 上使用 Model Y 橡胶举升垫，在 Model 3 上使用 Model 3 举升垫。

    通用举升垫适配器说明：

    1. 将与举升机类型相匹配的正确螺纹适配器安装到举升机适配器上。
    2. 确保将螺纹止动垫圈正确安装并紧固至举升机适配器底部。如果未安装螺纹止动垫圈，请勿继续使用举升机适配器。
    3. 将举升机适配器安装到举升臂上，使黑色的举升垫朝向车辆。
      Warning
      确保适配器安装方向正确。
    4. 调整举升臂位置，使举升机适配器与车辆上的固定销孔对齐。
    5. 抬起举升臂，将举升垫完全放置到车辆上。
    6. 确保所有 4 个适配器均已完全就位在车辆上。
  50. Raise and lock the vehicle at a comfortable working height.
    CAUTION
    Verify that the vehicle is stable on the lift.
  51. Remove the front aero shield panel. See 面板 - 流线型护板 - 前（非结构化电池组）（拆卸和更换）.
  52. Remove the bolt and clips that attach the LH front wheel liner to the HV battery and lower wheel well area. Repeat this step for the RH side of the vehicle.
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
  53. Remove the front HV battery skid plate. See 滑板 - 高压电池 - 前部（拆卸和更换）.
  54. Release the connector lock, and then disconnect the A/C compressor electrical connector from the HV harness.
  55. Install bungee straps to pull the LH and RH front wheel arch liners away from the HV battery and expose the coolant hoses.
  56. Perform a rear powertrain coolant drain. See 动力总成冷却液（排空和重新加注）.
  57. Perform a platter enclosure coolant drain. See 磁盘外壳冷却液（排放和重新加注）.
  58. Remove the mid aero shield panel. See 面板 - 流线型护板 - 后部（拆卸和更换）.
  59. Position the support stand underneath the front portion of the rear subframe.
  60. Release the fir tree clips that attach the coolant hoses to the LH shear plate.
  61. Remove the smaller bolts that attach the LH shear plate to the body.
    Tip
    推荐使用以下工具
    • 13 mm 套筒
  62. Remove and discard the larger bolt that attaches the LH shear plate and rear subframe to the body, and then remove the LH shear plate.
    Tip
    推荐使用以下工具
    • 21 毫米套筒
  63. Re-install the larger bolt, and hand-tighten the bolt to the rear subframe.
  64. Repeat step 60through 63 for the RH shear plate.
  65. Remove the support stand from underneath the rear subframe
  66. Remove the rear HV battery skid plate. See 滑板 - 高压电池 - 后部（拆卸和更换）.
  67. Position the coolant drain under the rear LH side of the HV battery.
  68. Release the clip and disconnect the rear drive unit inverter inlet hose from the rear of the HV battery, and immediately plug the male and female fittings.
  69. Position the coolant drain under the rear RH side of the HV battery.
  70. Release the clip and disconnect the coolant outlet hose to rear powertrain return coupling, and immediately plug the male and female fittings.
  71. Remove the coolant drain from underneath the vehicle.
  72. Remove the nut that attaches the rear drive unit HV electrical harness bracket to the HV battery.
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
  73. Slide the release to unlock the HV battery rear drive unit connector handle of the rear drive unit to HV battery harness from the secured position.
  74. Fully raise the handle on the HV battery rear drive unit connector.
  75. Remove the HV battery rear drive unit connector from the HV battery header.
  76. With an assistant, put the battery table in position, and then lower the vehicle to support the HV battery.
    Note
    Line up the battery table so that the center 4 bolts of the HV battery are accessible through the opening in the battery table.
  77. Remove the center bolts (x4) that attach the HV battery through the HV battery center rail ski cover.
    Tip
    推荐使用以下工具
    • 外梅花套筒 Plus EP14
  78. Remove the bolts (x8) that attach the HV battery LH and RH support brackets to the vehicle.
    Tip
    推荐使用以下工具
    • 16 毫米套筒
  79. Remove the bolts (x16) that attach the HV battery to the vehicle.
    Note
    Record the positions of any installed washers, as they will be reinstalled to the same locations during the installation procedure.
    Tip
    推荐使用以下工具
    • 13 mm 套筒
  80. With an assistant, raise the vehicle and remove the HV battery from underneath the vehicle.
  81. Remove the ancillary bay perimeter seal from the HV battery pack.

安装

  1. Install a new HV battery cover gasket. See 密封件 - 外围 - 高压电池（拆卸和更换）.
  2. Inspect the top cover of the HV battery for the presence of NVH pads.
    • If the HV battery already has NVH pads, continue to the next step.
    • If the HV battery does not have NVH pads, install the NVH pads. See NVH 垫 - 高压电池（安装）.
      Note
      Add correction code 16103101 to the Repair Order separately. The labor time to install the NVH pads is not included in this parent procedure.
  3. Clean the busbar HV connector contact surface of residual Penetrox.
    Note
    Allow one minute of drying time after removing Penetrox.
  4. Clean the HV connector contact surface of residual Penetrox.
    Note
    Allow one minute of drying time after removing Penetrox.
  5. Install the HV battery alignment rods; 2 at the front of the vehicle and 2 at the HV battery near the ancillary bay.
    Figure 1. RH front alignment rod shown; LH similar
    Figure 2. Rear alignment rods
  6. With an assistant, position the HV battery underneath the vehicle.
  7. Lower the vehicle to the HV battery, and with an assistant, align the holes with the alignment rods.
    Note
    Do not fully lower the vehicle onto the HV battery. The battery will still need to slightly move to install the bolts in the following steps.
    CAUTION
    Make sure that the coolant hoses and HV harnesses are not caught on the alignment rods or sandwiched between the HV battery and the vehicle.
  8. Install and hand-tighten the LH and RH bolts (x16) that attach the HV battery to the body.
    Note
    Install the washers to the locations recorded earlier during removal.
  9. Remove HV battery front alignment rods.
  10. Install and hand-tighten the bolts (x8) that attach the HV battery LH and RH support brackets to the vehicle.
  11. Install and hand-tighten the bolts (x4) that attach the center portion of the HV battery through the HV battery center rail ski cover.
  12. Open the LH rear door
  13. Remove the HV battery alignment rod from the LH rear inner bolt location.
  14. Install and hand-tighten the LH rear inner HV battery bolts.
  15. Lift the carpet flap, and then install and hand-tighten the LH middle inner HV battery bolt.
  16. Close the LH rear door and open the LH front door.
  17. Install and hand-tighten both LH front inner HV battery bolts.
  18. Repeat step 12 through step 17 for the RH side of the vehicle.
  19. Fully lower the vehicle onto the HV battery.
  20. Torque the LH and RH bolts (x16) that attach the HV battery to the vehicle.
    35 Nm (25.8 lbs-ft)
    Tip
    推荐使用以下工具
    • 13 mm 套筒
  21. Torque the bolts (x8) that attach the HV battery LH and RH support brackets to the vehicle.
    110 Nm (81.1 lbs-ft)
    Tip
    推荐使用以下工具
    • 16 毫米套筒
  22. Torque the bolts (x4) that attach the center portion of the HV battery through the center ski cover.
    35 Nm (25.8 lbs-ft)
    Tip
    推荐使用以下工具
    • 外梅花套筒 Plus EP14
  23. With an assistant, raise the vehicle, and then remove the battery table from underneath the vehicle.
  24. Set the vehicle to a comfortable working height, and then lower the vehicle into locks.
  25. Position the support stand to support the front portion of the rear subframe.
  26. Remove the smaller bolts (x2) and the larger bolt that are used to attach the LH shear plate to the vehicle.
    Figure 3. LH shown, RH similar
  27. Install the LH shear plate, and then install and hand-tighten the larger bolt that attaches the shear plate to the vehicle.
  28. Install and hand-tighten the smaller bolts (x2) that attach the shear plate to the HV battery.
    Figure 4. LH shown, RH similar
  29. Torque the large bolt that attaches the LH shear plate to the body.
    130 Nm (95.9 lbs-ft)
    Tip
    推荐使用以下工具
    • 21 毫米套筒
  30. Torque the small bolts that attach the LH shear plate to the body.
    35 Nm (25.8 lbs-ft)
    Tip
    推荐使用以下工具
    • 13 mm 套筒
  31. Repeat step 26 through step 30 for the RH shear plate.
  32. Remove the support stand from underneath the rear subframe
  33. Fasten the fir tree clips that attach the coolant hoses to the LH and RH shear plates.
    Figure 5. LH shown, RH similar
  34. Fully raise the handle on the HV battery rear drive unit connector of the rear drive unit to HV battery harness.
  35. Install the HV connector special tool onto the HV battery rear drive unit connector.
  36. Use both hands to firmly connect the HV battery rear drive unit connector of the rear drive unit to HV battery harness to the HV battery header.
    CAUTION
    Make sure that the connector fits the header squarely and tightly, and that both retention pins enter the handle.
  37. Remove the HV connector special tool from the HV battery rear drive unit connector.
  38. While pressing the HV battery rear drive unit connector onto the HV battery header, fully lower the handle.
    CAUTION
    Make sure that the handle does not bind as it is lowered.
  39. Slide the release to lock the HV battery rear drive unit connector handle in the secured position.
  40. Verify that the HV battery rear drive unit connector is fully seated, and compare both sides of the connector that it is properly secured in place.
    Note
    An improperly seated connector might lead to connector damage and rear drive unit problems later on.
  41. Install the nut that attaches the rear drive unit HV electrical harness bracket to the HV battery.
    10 Nm (7.4 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
  42. Position the coolant drain beneath the RH rear of the HV battery.
  43. Remove the hose plugs, and then connect coolant outlet hose to rear power train return hose.
    CAUTION
    执行推拉测试，确认软管已完全就位。
  44. Position the coolant drain underneath the LH rear of the HV battery.
  45. Remove the hose plugs, and then connect rear drive unit inverter inlet hose to the rear of HV battery.
    CAUTION
    执行推拉测试，确认软管已完全就位。
  46. Remove the coolant drain from underneath the vehicle.
  47. Install the rear HV battery skid plate, but only hand-tighten the fasteners. See 滑板 - 高压电池 - 后部（拆卸和更换）.
  48. Torque the fasteners that attach the rear skid plate to the vehicle. See 滑板 - 高压电池 - 后部（拆卸和更换）.
  49. Install the mid aero shield panel. See 面板 - 流线型护板 - 后部（拆卸和更换）.
  50. Position the coolant drain under the front LH side of the HV battery.
  51. Fasten the clips that attach the HV battery front manifold hose to the body.
  52. Remove the plugs from the chiller to HV battery hose and the manifold at the LH side of the vehicle, immediately connect the male and female fittings, and then fasten the clip.
    Note
    Perform a push-pull-push test on the fittings to make sure that they are secure.
  53. Remove the plugs from the HV battery return hose at the LH side of the vehicle, immediately connect the male and female fittings, and then fasten the clip.
    Note
    Perform a push-pull-push test on the fittings to make sure that they are secure.
  54. Position the coolant drain under the front RH side of the HV battery.
  55. Remove the plugs from the rear powertrain supply hose at the RH side of the vehicle, immediately connect the male and female fittings, and then fasten the clip.
    Note
    Perform a push-pull-push test on the fittings to make sure that they are secure.
  56. Remove the plugs from the powertrain return hose at the RH side of the vehicle, immediately connect the male and female fittings, and then fasten the clip.
    Note
    Perform a push-pull-push test on the fittings to make sure that they are secure.
  57. Remove the coolant drain from underneath the vehicle.
  58. Remove the plastic bracket that attaches the HV connectors to the HV battery.
  59. Connect the A/C HV connector, and then engage the connector lock.
  60. Install the front HV battery skid plate. See 滑板 - 高压电池 - 前部（拆卸和更换）.
  61. Remove the bungee straps from the LH and RH wheel arch liners.
  62. Install the bolt and clips that attach the LH front wheel liner to the HV battery and lower wheel well area. Repeat this step for the RH side of the vehicle.
    5 Nm (3.7 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
  63. Install the front aero shield panel. See 面板 - 流线型护板 - 前（非结构化电池组）（拆卸和更换）.
  64. Lower the vehicle fully.
  65. Remove the chock, and with an assistant, push the vehicle away from the lift to a stall, and then re-chock the wheel.
    CAUTION
    Push the vehicle for a very short distance and at less than 1 MPH.
  66. Install the nut that attaches the positive 12V output to the PCS cable, and then close the cover.
    9 Nm (6.6 lbs-ft)
    CAUTION
    Ensure the rubber boot is not pinched between the cable terminal and pass through.
    CAUTION
    确保正极输出电缆的位置正确，并且沿正确方向紧贴直流-直流直通件的塑料防旋转边缘。
    Tip
    推荐使用以下工具
    • 13 mm 套筒
  67. Install a new nut that attaches the DCDC ground strap to the HV battery.
    9 Nm (6.6 lbs-ft)
    Tip
    推荐使用以下工具
    • 13 毫米 12 角深套筒
  68. Remove the logic cap, and then connect the HVC logic connector.
  69. Apply a small amount of Penetrox onto the HV connector joints.
  70. Position the busbar kit connector and lower onto the HV header.
  71. Install the bolts that attach the charge port busbar kit to the HV header.
    9 Nm (6.6 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米深套筒
  72. Perform a zero adjust of the Hioki resistance meter in preparation to measure resistances. See 电阻表（零点调节）.
  73. Put on HV insulating gloves and leather over gloves.
  74. At the ancillary bay, use the Hioki resistance meter to measure the resistance between the charge port busbar lead and the ancillary bay HV header bolt head. Also perform this test on the other lead and bolt head.
    Note
    The acceptable resistance is between 0.050 mΩ (50 μΩ) and 0.195 mΩ (195 μΩ). If the measured resistance is above 0.195 mΩ (195 μΩ), there is too much resistance in the High Voltage joint. Remove the fastener, clean areas with isopropyl alcohol, install fastener back and test again, as appropriate.
    Note
    If the resistance is lower than 0.050 mΩ (50 μΩ), reposition the probes and measure again. If after 4 attempts the resistance is consistently lower than 0.050 mΩ (50 μΩ), the test has passed; continue to the next step.
  75. Remove the HV insulating gloves and leather over gloves.
  76. Install the bolt that secures the busbar cover access door.
    9 Nm (6.6 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米深套筒
  77. 如果充电接口和高压电池之间有一个三相（交流）连接点，请将其连接：
    1. 将充电接口至高压电池线束的三相连接器把手抬至最高处。
    2. 用双手将充电接口至高压电池线束的三相连接器牢固连接到高压电池仓三相接头上。
      CAUTION
      确保连接器与接头稳固连接。
    3. 将三相连接器按压到三相接头上，同时将把手降至最低处。
      CAUTION
      确保把手在降下时不扭结。
    4. 滑动释放装置，将三相连接器把手锁定在固定位置。
    5. 确认连接器完全就位，然后比对连接器两侧，确保正确锁定到位。
      Note
      连接器就位不当可能在日后导致连接器损坏和充电故障。
  78. Install the clip that attaches the logic electrical harness to the LH seat frame.
  79. Connect the logic connector at the LH seat frame.
  80. Connect the 2nd row 40 seat connector.
    Note
    There may be a red locking tab on newer models.
  81. Position the 2nd row 60 seat assembly into the vehicle.
    Note
    Recommend assistance.
  82. Move the 2nd row 60 seat back to vertical position.
  83. Install the new bolts (x5) (1616775-00-B) that attach the 2nd row 60 seat frame to the body, and torque them in the sequence: outboard front → both inboard rear → outboard rear → inboard front.
    37 Nm (27.3 lbs-ft)
    Note
    Bottom seat bolts are located behind the main carpet.
    Note
    Use of the following tool(s) is recommended:
    • 11 mm socket
    • Cordless 3/8in Dr Impact
    • 6 in extension
  84. Connect the 2nd row 60 seat connector and engage the locking tab.
  85. Secure the 2nd row 60 seat connector to the LH seat frame.
  86. Torque the LH and RH rear inner HV battery bolts.
    66 Nm (48.7 lbs-ft)
    Tip
    推荐使用以下工具
    • 16 毫米套筒
  87. Remove the folded shop towel from underneath the rear cabin carpet.
  88. Install the clips (x3) that attach the rear carpet to the vehicle.
  89. Install the clip securing the LH lower B-pillar to body.
  90. Install the LH lower C-pillar trim. See 饰板 - C 柱 - 下 - 左侧（拆卸和更换）.
  91. Repeat steps 89 and 90 for the RH side of the vehicle.
  92. Install the 2nd row lower seat cushion. See 座椅座垫 - 下部 - 第二排（拆卸和更换）.
  93. Torque the LH middle inner HV battery bolt, and then fold the carpet to its original position. Repeat this step on the RH side of the vehicle.
    66 Nm (48.7 lbs-ft)
    Tip
    推荐使用以下工具
    • 16 毫米套筒
  94. Install the 2nd row floor mat into the vehicle.
  95. Torque both RH front inner HV battery bolts, and then install the foam plugs.
    136 Nm (100.3 lbs-ft)
    Tip
    推荐使用以下工具
    • 梅花 Plus EP20 套筒
  96. Fold the RH front main cabin carpet forward to its original position, and then install the clip that attaches the LH carpet to the vehicle.
  97. Install the RH lower A-pillar trim. See 饰板 - A 柱 - 下 - 左侧（拆卸和更换）.
  98. Install the RH middle A-pillar trim. See 饰板 - A 柱 - 中部 - 左侧（拆卸和更换）.
  99. Install the RH instrument panel end cap. See 端盖 - 仪表板 - 左侧（拆卸和更换）.
  100. Install the RH center console side panel carpet. See 侧板 - 中控台 - 左侧（拆卸和更换）.
  101. Install the RH front floor mat.
  102. Install the front passenger footwell cover. See 盖板 - 脚部空间 - 驾驶位（拆卸和更换）.
  103. Repeat step 95 through step 102 for the LH side of the vehicle.
  104. Perform a cooling system vacuum refill. See 冷却系统（真空再加注）.
  105. Connect 12V power. See 12V/低压电源（断开和连接）.
  106. On the vehicle touchscreen, press and hold the park button to release EPB service mode.
  107. 通过“维护模式”或 Toolbox 执行以下例行程序（请参阅0005 - 维护模式）： TEST_VCFRONT_X_THERMAL-COOLANT-AIR-PURGEvia Service Mode:
    • Thermal ➜ Actions ➜ Coolant Purge Stop or Coolant Purge Start
    • Thermal ➜ Coolant System ➜ Coolant Purge Start
    via Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Coolant Air Purge
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Coolant Air Purge
    via Toolbox:(link)
  108. Inspect the coolant level and top off as necessary, and then install the coolant bottle cap.
    Note
    Ensure that the coolant level is at the "Max" line.
  109. 通过“维护模式”或 Toolbox 执行以下例行程序（请参阅0005 - 维护模式）： TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Service Mode:Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
    via Toolbox:(link)
  110. Install the rear underhood apron. See 前备箱挡板 - 后部（拆卸和更换）.
  111. Raise all windows and close all doors.
  112. Remove lift pads from the LH rocker.
  113. Install the butyl patch that covers the LH rocker access holes.
  114. Install the LH rocker panel carrier. See 支架 - 门槛板 - 左侧（拆卸和更换）.
  115. Install the LH lower rocker panel cover. See 盖板 - 门槛板 - 下 - 左侧（拆卸和更换）.
  116. Repeat step 112 though step 115 for the RH side of the vehicle.