30/08/2022 20:29:18
制动管路 - 主缸至防抱死制动系统(结构化电池组)(左侧驾驶)(拆卸和更换)
校正代码 33034012 1.62 注意:除非本程序中另有明确规定,否则上述校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。注意:请参阅平均维修工时,深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈,请发送电子邮件至LaborTimeFeedback@tesla.com。注意:请参阅人员保护,确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
拆卸
- Open the LH front door and lower the LH front window.
- Remove the rear underhood apron. See 前备箱挡板 - 后部(拆卸和更换).
- Remove the underhood storage unit. See 前备箱储物单元(拆卸和更换).
- Disconnect 12V power. See 12V/低压电源(断开和连接).
- Remove the 12V battery. See 12V/低压电池(拆卸和更换).
- Remove front aero shield. See 面板 - 流线型护板 - 前(结构化电池组)(拆卸和更换).
- Disconnect the electrical connector from the ABS unit.
- Position the oil drain under the ABS unit.
-
Loosen the nut that attaches the
master cylinder secondary brake line to the ABS unit.
-
Loosen the nut that attaches the primary cylinder secondary brake line to the ABS
unit.
- Place an absorbent material beneath the brake booster and reservoir area.
- Using a brake fluid syringe, remove the brake fluid from the reservoir.
-
Loosen the nut that attaches the secondary brake line to the master cylinder, and
then remove the secondary brake line.
-
Loosen the nut that attaches the
primary brake line to the master cylinder, and then remove the primary brake line.
-
Release the primary and secondary
brake lines from the brake line bundle clip.
-
Loosen the harness clip that attaches
the master cylinder brake lines to the rear of the hydraulic control unit bracket.
-
Route the master cylinder brake lines
towards the front controller, and then remove the master cylinder brake line bundle from
the vehicle.
安装
- Place the master cylinder brake line bundle into position for installation
-
Install the secondary brake line to the master cylinder, and then fasten the nut that
attaches the secondary brake line.
-
Install the primary brake line to the master cylinder, and then fasten the nut that
attaches the primary brake line.
- Remove the absorbent material from underneath the brake booster and brake fluid reservoir area.
-
Install the harness clip that attaches the master cylinder brake lines to the rear of
the hydraulic control unit bracket.
-
Attach the primary and secondary brake lines to the brake line bundle clip.
-
Fasten the nut that attaches the master cylinder secondary brake line to the ABS
unit.
-
Fasten the nut that attaches the primary cylinder secondary brake line to the ABS
unit.
- Clean the ABS unit surface of residual brake fluid.
- Remove the oil drain container from underneath vehicle
- Reconnect 12V power. See 12V/低压电源(断开和连接).
- Bleed the brakes. See 制动液排放/冲洗
- Install the front aero shield. See 面板 - 流线型护板 - 前(结构化电池组)(拆卸和更换).
- Install the HEPA filter. See 总成 - 过滤器 - 高效分子空气 (HEPA)(拆卸和更换).
- Install the underhood storage unit. See 前备箱储物单元(拆卸和更换).
- Install the rear underhood apron. See 前备箱挡板 - 后部(拆卸和更换).
-
Perform a test drive.
注Per current FRT (00040100) 0.3 hrs, If alignment was adjusted verify tracking, If DAS components were adjusted verify operation, If brakes were serviced perform burnishing