08/08/2023 20:25:27
支架 - 前端(带加热泵款)(拆卸和更换)
校正代码 10101012 注意:除非本程序中另有明确规定,否则上述校正代码和 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。 注意:请参阅平均维修工时,深入了解 FRT 及其创建方式。要提供有关 FRT 值的反馈,请发送电子邮件至LaborTimeFeedback@tesla.com。 注意:请参阅人员保护,确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。
警告
尽管此程序已经过验证,但仍是一个草案。可能没有警告和注意事项。请遵守安全要求,处理或靠近高压系统和部件时,请谨慎操作。请将校正修理内容及反馈发送至ServiceDevelopment@teslamotors.com。
拆卸
-
Open LH front door
-
Open hood
注Press "Open" button on touchscreen to release latch, Lift lid manually
-
Remove rear apron
注12x clips, Only store rear apron visible face upwards
-
Remove cabin intake upper duct
assembly
注3x clips, Some configurations may come with 4x clips
-
Remove closeout panel from frunk
assembly
注4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Grab closeout panel from bottom then pull it upward to release clips, Disconnect switch
-
Remove bolts securing frunk
assembly
注7x bolts, 10mm, 5 Nm, Lift up RBN covers to access upper fasteners, Newer vehicles may not be equipped with covers
-
Remove frunk assembly from
vehicle
注12x clips, Replace any clips if broken or missing, Number of clips may vary on older vehicles
-
Remove fasteners holding upper portion
of front fascia to vehicle
注6x bolts, 10mm, 4 Nm
-
Remove push clips securing LH front
wheel arch liner to fascia and move to the side for access
注5x push clips, Turn the steering wheel to the RH for additional clearance between front wheel arch liner
-
Loosen forward bolts securing LH
corner of front fascia to fender
注2x bolts, 10mm, 4 Nm
-
Remove bolt securing LH corner of
fascia to fender
注1x bolt, 10mm, 3 Nm
-
Remove push clips securing RH front
wheel arch liner to fascia and move to the side for access
注5x push clips, Turn the steering wheel to the LH for additional clearance between wheel arch liner
-
Loosen forward bolts securing RH front
corner of front fascia to fender
注2x bolts, 10mm, 4 Nm
-
Remove bolt securing RH front corner
of front fascia to fender
注1x bolt, 10mm, 3 Nm
-
Disconnect 12V harness for front
fascia
注1x locking connector, Release the locking tab by sliding it away from the connector, Then depress the grey lock to release the connector
-
Remove bolts securing valance to front
aero shield
注4x bolts, 10mm, 5 Nm
-
Release both front corners then
release front of front fascia by pulling upward and away from vehicle and place onto
padded surface
注8x clips, Recommend assistance, Use caution not to damage headlamp or fender during removal
-
Disconnect active grille shutter
actuator connector
注1x locking electrical connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector
-
Remove ambient temperature sensor
cover from active grille shutter
-
Disconnect ambient temperature sensor
connector
注1x connector
-
Disconnect hood latch open
switch
注1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector
-
Disconnect hood latch actuator
注1x connector
-
Remove hood latch actuator from front
end carrier
注2x bolts, 10mm, 5 Nm
-
Remove hood latch from front end
carrier
注2x bolts,10mm, 8 Nm, Mark latch location for alignment when installing
-
Remove LH center fascia reinforcement
from front end carrier
注1x tab, 2x datums, Release locking tab under fascia reinforcement, then pull straight up to release fascia reinforcement
-
Remove RH center fascia reinforcement
from front end carrier
注1x tab, 2x datums, Release locking tab under fascia reinforcement, then pull straight up to release fascia reinforcement
-
Disconnect front acceleration
sensors
注1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector, Disconnect LH, RH, and center front acceleration sensor
-
Remove bolts securing front bumper
beam with energy absorber to LH crush can
注2x bolts, 15mm, 75 Nm
-
Remove bolts securing front bumper
beam with energy absorber to RH crush can
注2x bolts, 15mm, 75 Nm
-
Remove front bumper beam with energy
absorber
注Use a pry bar as needed to remove front bumper beam, Be cautious when prying not to damage body, Slightly tap with dead blow hammer to assist with removal as needed
-
Disconnect LH FEM harness
connector
注1x locking connector, Disengage locking tab
-
Disconnect RH FEM harness
connector
注1x locking connector, Disengage locking tab
-
Remove radar assembly harness clip
from FEM radar bracket
注1x clip
-
Disconnect radar assembly
connector
注1x connector
-
Remove the FEM radar bracket from
front end carrier
注4x bolts, 10mm, 8 Nm
-
Install bungee cords and support
cooling fan module assembly
注2x bungee cord
-
Remove RH bolt securing cooling fan
module assembly to front end carrier
注1x bolt, 8mm, 10 Nm, Recommend assistance to support the cooling fan module assembly
-
Remove LH bolt securing cooling fan
module assembly to front end carrier
注1x bolt, 8mm, 10 Nm, Recommend assistance to support the cooling fan module assembly
-
Remove lower bolts securing front end
carrier to vehicle
注4x bolts, 13mm, 16 Nm
-
Remove ankle catcher from front end
carrier
注2x datums, Slightly pull carrier outward to clear datum from ankle catcher
-
Remove upper bolts securing front end
carrier to vehicle and remove front end carrier
注2x bolts, 13mm, 16 Nm
-
Remove FEM harness from front end
carrier
注5x clips
安装
-
Install FEM harness to front end
carrier
注5x clips
-
Position front end carrier to vehicle
and install upper bolts securing front end carrier hand tight
注2x bolts, 13mm, 16 Nm, Torque at later step
-
Position the ankle catcher onto the
front end carrier
注2x datums, Slightly pull carrier outward to secure ankle catcher onto datums
-
Install lower bolts securing front end
carrier to vehicle
注4x bolts, 13mm, 16 Nm
-
Torque upper bolts securing front end
carrier to vehicle
注2x bolts, 13mm, 16 Nm
-
Install bolts securing cooling fan
module to front end carrier
注2x bolts, 8mm, 10 Nm
-
Remove bungee cords supporting cooling
fan module assembly
注2x bungee cords
-
Install the FEM radar bracket to front
end carrier
注4x bolts, 10mm, 8 Nm
-
Connect radar assembly connector
注1x connector
-
Install radar assembly harness clip to
FEM radar bracket
注1x clip
-
Connect RH FEM harness connector
注1x connector, Engage locking tab
-
Connect LH FEM harness connector
注1x connector, Engage locking tab
-
Position front bumper beam with energy
absorber
注Use a dead blow hammer as needed to install front bumper beam into front crush cans
-
Install bolts securing front bumper
beam with energy absorber to LH crush can
注2x bolts, 15mm, 75 Nm
-
Install bolts securing front bumper
beam with energy absorber to RH crush can
注2x bolts, 15mm, 75 Nm
-
Connect front acceleration
sensors
注3x connectors, Engage locking tab, Connect LH, RH, and center front acceleration sensors
-
Install RH center fascia reinforcement
to front end carrier
注1x tab, 2x datums, Engage locking tab, Push straight down for installation
-
Install LH center fascia reinforcement
to front end carrier
注1x tab, 2x datums, Engage locking tab, Push straight down for installation
-
Install hood latch to front end
carrier
注2x bolts,10mm, 8 Nm, Hand tighten bolts and make fine adjustments, Align hood latch with marked locations
-
Install hood latch actuator onto front
end carrier
注2x bolts, 10mm, 5 Nm
-
Connect hood latch actuator
注1x connector
-
Connect the hood latch open switch
connector
注1x connector, Engage locking tab
-
Connect ambient temperature sensor
connector
注1x connector
-
Install ambient temperature sensor
cover into active grille shutter
-
Install connector to active grille
shutter actuator
注1x connector , Engage locking tab
-
Install front fascia onto vehicle and
secure front clips and both front corners
注8x clips, Recommend assistance, Use caution not to damage headlamp or fender during installation
-
Secure 12V harness for front
fascia
注1x connector, Engage the locking tab
-
Install rear bolt and tighten all
three bolts securing RH front corner of front fascia to fender
注1x bolt, 10mm, 3 Nm, 2x bolts, 10mm, 4 Nm, Most forward bolts, Align fascia to fender before tightening
-
Install push clips securing RH front
wheel liner to fascia
注5x push clips
-
Install rear bolt and tighten all
three bolts securing LH front corner of front fascia to fender
注1x bolts, 10mm, 3 Nm, 2x bolts, 10mm, 4 Nm, Most forward bolts, Align fascia to fender before tightening
-
Install push clips securing LH front
wheel liner to fascia
注5x push clips
-
Apply Loctite 222 onto front aero
shield forward bolts and install fasteners to front aero shield
注4x bolts, 10mm, 5 Nm
-
Install fasteners holding upper
portion of front fascia to vehicle
注6x bolts, 10mm, 4 Nm
-
Install frunk assembly to
vehicle
注12x clips. Make sure frunk assembly is fully seated onto clips. Number of clips may vary on older vehicles. Ensure A/C compressor HVIL harness is not pinched between frunk assembly and thermal beam.
-
Install bolts securing frunk
assembly
注7x bolts, 10mm, 5 Nm, Lower RBN covers after installing upper fasteners, Newer vehicles may not be equipped with covers
-
Close the hood to check the hood
alignment with fascia/fender
-
Open hood and make adjustments if
necessary
注2x bolts,10mm, 8 Nm, If adjustments are not necessary, Torque bolts
-
Install frunk close out panel
注4x clips, 1x connector, Frunk safety switch, 3x guide tabs, Align 3x tabs then push downward to secure clips
-
Install cabin intake upper duct
assembly
注3x clips, Some configurations may come with 4x clips
-
Install rear apron
注12x clips
-
Close hood
-
Close LH front door