04/09/2024 16:56:09

Tire - Front - LH (Repair)

Correction Code 34023008

Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Always read and understand the tire equipment operator’s manual and on-screen instructions before operating the wheel balancer or tire changer.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Always make sure to properly secure the wheel and exercise caution around all moving parts and pinch points, including the indent rollers. Additionally, secure all loose items such as hair, jewelry, and clothing, so that they will not catch on moving parts.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Wear appropriate personal protective equipment (PPE) including cut-resistant gloves and safety glasses when performing this procedure.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The machine must be operated by no more than one person at a time. Other persons must maintain a safe distance of at least three feet from equipment while in use.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Never use equipment that is defective or not working as expected based on the equipment operator’s manual.
Informational PurposesAn informational icon, calling your attention
Note
These instructions are based on the Hunter GSP9700 wheel balancer. Some steps might be different for other wheel balancers. Refer to the operator's manual and on-screen instructions for specific information.
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
Only use cleaning agents and solvents in a well-ventilated area.
Figure 1. MY Shown, Other Models Similar
Warning IconA warning icon, calling your attention to a possibly risky situation
Warning
The video(s) included in this procedure are meant as an overview for supplemental purposes only. Follow all of the steps listed in the procedure to avoid damage to components and/or personal injury.

Special tool(s) required for this procedure:

Supplier Part Number Description
1081319-00-A Hoe style inner liner scraper
1081320-00-A Air tool 2500 RPM buffer with quick change chuck
1081322-00-A 2 1/2" light duty carbide buffing wheel
1081321-00-A Buffer exhaust hose kit
1081323-00-A 7/32" carbide cutter
1081325-00-A 3/16" x 1 1/2" wood handle ball bearing stitcher
1081326-00-A Manual tire spreader
  1. Visually inspect the tire. If any of the following are noted, discontinue this procedure and replace the tire:
    • The puncture is on the shoulder or sidewall
      1Non-repairable areas
      2Repairable area
    • The foreign object entered the tire at an angle of more than 15 degrees from perpendicular to the tread surface
    • The foreign object is more than 1/4 in (6.3 mm) in diameter
    • The tread depth is less than 2/32 in (1.6 mm)
    • There is oxidation or weather cracking on the sidewall that is deeper than 2/32 in (1.6 mm)
    • The tire is more than 10 years old
  2. Dismount the tire from the wheel (refer to procedure).
  3. Place the tire on the tire spreader, with the puncture facing down.
  4. Spread the sidewalls to create a larger working area.
  5. Visually inspect the entire inside of the tire. If any of the following are noted, discontinue this procedure and replace the tire:
    • Evidence of the tire being driven while flat (inner sidewall cracking, separated, or blue in color)
    • A previous repair is close enough to the new puncture that the repair areas will overlap
    • Previous improper repairs
    • Broken, kinked, or damaged beads
    • Any other internal damage
    • The foreign object is more than 1/4 in (6.3 mm) in diameter
  6. If the vehicle was outdoors in temperatures below 50 degrees F (10 degrees C), use a heat gun or other heat source to thoroughly warm the tire.
  7. Use the paint stick to mark the area around the puncture on the inside and outside of the tire.
  8. Confirm the path of the foreign object (the puncture channel). The puncture channel must be no more than 15 degrees from perpendicular to the tread surface. If the puncture channel is more than 15 degrees, discontinue this procedure and replace the tire.
  9. Remove the foreign object from the tire.
  10. If the tire has an interior foam noise absorber:
    1. Cut out a section of foam around the marked area, 50 mm from each side of the puncture.
      Warning IconA warning icon, calling your attention to a possibly risky situation
      CAUTION
      Take care not to damage component(s).
    2. Remove and discard the foam section.
  11. Use the carbide cutter to clear the puncture channel.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Use a low speed (under 1200 RPM) only. Excessive speed damages the rubber surrounding the puncture channel, increasing the chances of future leakage.
  12. Hold the Minicombi insert over the puncture channel. Use the paint stick to draw an outline that is approximately 15 mm larger than the diameter of the Minicombi insert.
  13. Remove the Minicombi insert.
  14. Apply pre-buff cleaner to the outlined area. Wait at least 5 seconds before continuing to the next step.
  15. Use the inner liner scraper to scrape the outlined area.
  16. Repeat the previous 2 steps until the outlined area is fully cleaned.
  17. Use the buffer to lightly buff the outlined area until it is smooth.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    CAUTION
    Do not remove too much rubber. If the cords are exposed, the tire must be replaced.
  18. Vacuum the debris from the inside of the tire.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    To avoid contamination, do not let the vacuum nozzle touch the buffed area. Contamination prevents the Minicombi insert from adhering properly, which can result in tire failure, leading to serious injury or death.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Do not use compressed air to clean the buffed area. Compressed air contains moisture and oil that prevent the Minicombi insert from adhering properly, which can result in tire failure, leading to serious injury or death.
  19. Apply a thin, even layer of blue cement to the outlined area.
  20. Allow the cement to dry for at least 5 minutes, then test it by touching with a clean finger or knuckle. The cement is dry if it feels tacky. Wait until the cement dries before continuing to the next step.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    Allow the cement to dry naturally. Do not use compressed air, a fan, a heat gun, or other artificial means to force the cement to dry faster. Doing so prevents the Minicombi insert from adhering properly, which can result in tire failure, leading to serious injury or death.
    Tip: The cement dries faster if the tire is rotated so that the repair area is at the highest point of the tire.
  21. Rotate the tire so that the repair area is in a comfortable working location. Ensure that the sidewalls are not spread.
    Warning IconA warning icon, calling your attention to a possibly risky situation
    Warning
    The tire must be relaxed (sidewalls not spread) before continuing. If the sidewalls are spread, the Minicombi insert does not adhere properly, which can result in tire failure, leading to serious injury or death.
  22. Apply a small amount of blue cement to the puncture channel.
  23. Remove the Minicombi insert from the protective cover.
  24. Install the Minicombi insert:
    1. Insert the guide pin and stem from the inside of the tire.
    2. Use pliers to pull the guide pin from the outside of the tire until the rubber stem is visible.
    3. Use pliers to pull the rubber stem until the base of the Minicombi insert is flush with the tire and has a slight dimple.
      Informational PurposesAn informational icon, calling your attention
      Note
      The guide pin is not designed to pull the Minicombi insert through the tire.
  25. Roll the stitcher over the base of the Minicombi insert to fully adhere it to the tire. Start from the center of the base and roll toward the outside. Ensure that the whole base is thoroughly adhered to the tire.
  26. Remove the protective cover from the base of the Minicombi insert.
  27. Apply a generous amount of repair sealant to the base of the Minicombi insert and the buffed area.
    Informational PurposesAn informational icon, calling your attention
    Note
    Do not attempt to reattach the section of foam noise absorber that was removed earlier (if applicable).
  28. Mount the tire on the wheel (refer to procedure). Check for leakage.
  29. Cut off the exposed stem of the Minicombi insert so that the stem is flush with the tire tread.
  30. Rebalance the tire (refer to procedure).