2026-11-13

Brake Lines - 2 Tube Bundle (Remove and Replace)

Correction code 33035902 FRT 1.44 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure you are wearing proper PPE when performing the procedure below. NOTE: See Ergonomic Precautions for safe and healthy working practices.

Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.
  • 2026-11-11: Released new procedure.
  1. Open hood
    Note
    Via Controls > Front Trunk
  2. Remove rear underhood apron
    Note
    8x clips
  3. Remove LH underhood apron
    Note
    9x clips, (*Use this step for Model S Refresh procedures)
  4. Remove RH underhood apron
    Note
    9x clips
  5. Remove rear underhood apron
    Note
    8x clips
  6. Release primary and secondary drain tubes from cabin intake duct assembly
    Note
    2x hoses
  7. Release cabin intake duct assembly from cowl panel
    Note
    3x push clips
  8. Remove cabin intake duct assembly
    Note
    2x tabs, one on each side
  9. Remove HEPA filter outlet duct
    Note
    Lift up, Pull towards front of vehicle, Then rotate clockwise
  10. Remove underhood storage carpet
    Note
    2x connectors, Release edge of carpet from underneath underhood storage unit seal, Disconnect light and release switch connectors
  11. Release underhood storage unit
    Note
    2x bolts, 10mm, 7 Nm, 2x push clips
  12. Remove underhood storage unit
    Note
    1x grommet, Lift the underhood storage unit appropriately to access the grommet and push grommet through underhood storage
  13. Disconnect 12V battery negative terminal and First Responder Loop
    Note
    1x nut, 10mm, 5 Nm, 1x connector, Wait at least 2 minutes before disconnecting modules or HV components
  14. Remove fasteners securing battery beam to LH and RH body beams
    Note
    4x bolts, T30, 3.5 Nm, 1x edge clip, lift battery support assembly up to release support beam from under
  15. Release ground connections from LH frame
    Note
    3x grounding bolts, 13mm, torque?
  16. disconnect harnesses
    Note
    2x connectors
  17. Release barrel clips that secure brake lines to LH frame rail
    Note
    3x barrel clips, separate lines from clips for to prepare for break line removal step
  18. Loosen brake line nuts at master cylinder
    Note
    2x nuts, 12mm, 18 Nm
  19. Remove brake lines from master cylinder
    Note
    2x tubes, Place absorbent material below to catch residual fluid, unscrew brake line nuts by hand
  20. Loosen brake line nuts at ABS module
    Note
    2x nuts, 12mm, 23 Nm
  21. Remove brake lines from ABS module
    Note
    2x tubes, Place absorbent material below to catch residual fluid, unscrew brake line nuts by hand
  22. Place fender cover over painted areas
    Note
    If brake fluid is spilled on a painted surface, wash off immediately with clean water
  23. Remove brake line from LH frame rail
    Note
    Pull 2 line brake bundle upward while bending braided flexible lines around 4 line brake bundle and coolant hose
  24. Remove both lines from brake bundle individually
    Note
    Slide lines underneath A/C and coolant hose, Rotate upside down, gently pull up and out while guiding lines between coolant and A/C lines
  25. Install new 2 tube brake line bundle
    Note
    Insert individual lines between coolant and A/C line, Rotate and slide underneath A/C and coolant hose, New bundle comes with new anchor clips installed
  26. Position brake lines on LH frame rail
    Note
    Guide 2 line brake bundle downward while bending braided flexible lines under 4 line brake bundle and coolant hose
  27. Install brake lines to ABS module
    Note
    2x tubes, Hand tighten brake line nuts to avoid cross threading
  28. Tighten brake line nuts to ABS module
    Note
    2x nuts, 12mm, 23 Nm
  29. Install brake lines to master cylinder
    Note
    2x tubes, Hand tighten brake line nuts to avoid cross threading
  30. Tighten brake line nuts to master cylinder
    Note
    2x nuts, 12mm, 18 Nm
  31. Install clips that secure brake lines to LH frame rail
    Note
    3x barrel clips, install with enough space to clip lines back in before fully seating clips onto frame
  32. Install ground harnesses onto LH frame
    Note
    3x ground connectors, 13mm, torque?
  33. Reconnect harness connectors on LH side of frame
    Note
    2x connectors
  34. Install 12V battery beam
    Note
    4x bolts, T30, 3.5 Nm, 2x edge clips
  35. Connect First Responder Loop and 12V battery negative terminal
    Note
    1x connector, 1x nut, 10mm, 5 Nm, Connect First Responder Loop first
  36. Remove LH front lug nut covers
    Note
    5x covers
  37. Remove lug nut covers from LH rear wheel
    Note
    5x covers
  38. Remove lug nut covers from RH rear wheel
    Note
    5x covers
  39. Remove lug nut covers from RH front wheel
    Note
    5x covers
  40. Loosen LH front wheel
    Note
    5x nuts, 21mm, 175 Nm
  41. Loosen LH rear wheel
    Note
    5x nuts, 21mm, 175 Nm
  42. Loosen RH rear wheel
    Note
    5x nuts, 21mm, 175 Nm
  43. Loosen RH front wheel
    Note
    5x nuts, 21mm, 175 Nm
  44. Raise vehicle partially and lower onto locks
    Note
    Set vehicle to comfortable working height, Make sure there's an audible click of locks on both sides before lowering, otherwise vehicle may tilt to side
  45. Remove LH front wheel
    Note
    5x nuts, 21mm, 175 Nm
  46. Remove LH rear wheel
    Note
    5x nuts, 21mm, 175 Nm
  47. Remove RH rear wheel
    Note
    5x nuts, 21mm, 175 Nm
  48. Remove RH front wheel
    Note
    5x nuts, 21mm, 175 Nm
  49. Lower vehicle partially and set lift onto locks
    Note
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered, Set vehicle to comfortable working height
  50. Fill brake bleeder reservoir to full level
  51. Clean area around brake fluid reservoir and remove cap
  52. Top off reservoir
    Note
    If necessary
  53. Install pressure bleed adapter to reservoir
  54. Connect bleeder to adapter and set pressure to 30psi
  55. Connect laptop to vehicle with a tethered Ethernet connection via Toolbox 3
    Note
    1x connector, 2x clips, Newer models will access connector below MCU with cubby removed, Older models will access port at LH side of IP with end cap removedOpen Toolbox 3 website and establish connection to vehicle: https://toolbox.teslamotors.com, Select connection status icon at top right corner and select Connect Locally (icon will turn green when vehicle is connected), Local connection will enable service mode plus on display
  56. Run ODIN routine
  57. Remove bleeder covers from LH front caliper
    Note
    2x covers
  58. Install fluid catching bottle to LH front caliper outer bleeder valve and loosen valve
    Note
    Let the brake fluid drain for about 10 seconds or so before starting Toolbox bleeding routine
  59. Run ODIN routine PROC_ESP_FRONT-L-REAR-R_BRAKE-BLEEDvia Service Mode:Chassis ➜ Brakes ➜ Brake Bleed FL-RRvia Toolbox:(link)
  60. Run ODIN routine PROC_ESP_FRONT-L-REAR-R_BRAKE-BLEEDvia Service Mode:Chassis ➜ Brakes ➜ Brake Bleed FL-RRvia Toolbox:(link)
  61. Remove fluid catching bottle, Torque LH front brake caliper bleeding valves and install covers
    Note
    2x bleeding valves, 11mm, 18 Nm, 2x covers
  62. Remove bleeder covers from RH front caliper
    Note
    2x covers
  63. Install brake fluid catching bottle to RH front caliper outer bleeder valve and loosen valve
    Note
    Let the brake fluid drain for about 10 seconds or so before starting Toolbox bleeding routine
  64. Run ODIN routine PROC_ESP_FRONT-R-REAR-L_BRAKE-BLEEDvia Service Mode:Chassis ➜ Brakes ➜ Brake Bleed FR-RLvia Toolbox:(link)
  65. Run ODIN routine PROC_ESP_FRONT-R-REAR-L_BRAKE-BLEEDvia Service Mode:Chassis ➜ Brakes ➜ Brake Bleed FR-RLvia Toolbox:(link)
  66. Remove fluid catching bottle, Torque RH front brake caliper bleeding valves and install covers
    Note
    2x bleeding valves, 11mm, 18 Nm, 2x covers
  67. Remove bleeder cover from RH rear caliper
    Note
    1x cover
  68. Install fluid catching bottle to RH rear caliper bleeder valve and loosen valve
    Note
    Let the brake fluid drain for about 10 seconds or so before starting Toolbox bleeding routine
  69. Open RH rear brake caliper bleeding valve then Click play button next to PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEED and select "Run" to start ESP and then close bleeding valve once pump stops running
    Note
    1x bleeding valve, 10mm, 18 Nm
  70. Install bleeder cover onto RH rear caliper
    Note
    1x cover
  71. Remove bleeder cover from LH rear caliper
    Note
    1x cover
  72. Install fluid catching bottle to LH rear caliper bleeder valve and loosen valve
    Note
    Let the brake fluid drain for about 10 seconds or so before starting Toolbox bleeding routine
  73. Open LH rear brake caliper bleeding valve then Click play button next to PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEED and select "Run" to start ESP and then close bleeding valve once pump stops running
    Note
    1x bleeding valve, 10mm, 18 Nm
  74. Install bleeder cover onto LH rear caliper
    Note
    1x cover
  75. Turn off and remove brake pressure bleed adapter from the vehicle
  76. Check fluid level
    Note
    Top off if needed
  77. Install brake reservoir cap
  78. Remove fender cover
  79. Pump brake pedal few times to ensure pedal feels normal
  80. Perform Stiffness Test through Toolbox
    Note
    Select ‘Actions’ tab and search for 'IBST Stiffness Test - Service - BURNISHED/UNBURNISHED', Select 'TEST_BRAKE_X_STIFFNESS-TEST-SERVICE', select 'BURNISHED', If brake pads have been replaced select 'UNBURNISHED', click 'RUN', Do not press break pedal while routine is performed, Select ‘X’ at top right of window to close once complete, If the vehicle is equipped with a vacuum brake booster and the stiffness test cannot be performed, Skip this step
  81. Disconnect Toolbox from vehicle and install cubby
    Note
    1x connector, 2x clips, Ensure diagnostic cables are tucked into appropriate position then engage cubby
  82. Raise vehicle partially and lower onto locks
  83. Install LH front wheel
    Note
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  84. Install LH rear wheel
    Note
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  85. Install RH rear wheel
    Note
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  86. Install RH front wheel
    Note
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  87. Lower vehicle until tires are touching ground
    Note
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  88. Torque LH front wheel
    Note
    5x nuts, 21mm, 175 Nm
  89. Install LH front lug nut covers
    Note
    5x covers
  90. Torque LH rear wheel
    Note
    5x nuts, 21 mm, 175 Nm
  91. Install LH rear lug nut covers
    Note
    5x covers
  92. Torque RH rear wheel
    Note
    5x nuts, 21 mm, 175 Nm
  93. Install RH rear lug nut covers
    Note
    5x covers
  94. Torque RH front wheel
    Note
    5x nuts, 21mm, 175 Nm
  95. Install RH front lug nut covers
    Note
    5x covers
  96. Position underhood storage unit
    Note
    1x grommet, Lift the underhood storage unit appropriately to access the gromment and feed harness grommet through underhood storage unit
  97. Install bolts and clips securing underhood storage unit
    Note
    2x bolts, 10mm, 7 Nm, 2x push clips
  98. Install underhood storage carpet and reconnect light and release switch connectors
    Note
    2x connectors, Secure edges of carpet underneath underhood storage unit seal
  99. Install HEPA filter outlet duct
    Note
    First connect smaller end near firewall, then slide larger end onto HEPA filter assembly
  100. Install cabin intake duct assembly
    Note
    2x tabs, One on each side
  101. Secure cabin intake duct assembly to cowl panel
    Note
    3x push clips
  102. Secure primary and secondary drain tubes to cabin intake duct assembly
    Note
    2x hoses
  103. Install front underhood apron
    Note
    7x clips
  104. Install RH underhood apron
    Note
    9x clips
  105. Install LH underhood apron
    Note
    9x clips
  106. Install rear underhood apron
    Note
    8x clips
  107. Close hood
    Note
    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood
  108. Run ODIN routine
  109. Run ODIN routine PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)