Correction code 13016202

1. Open LH front door

   

2. Lower LH front window

   

3. Move LH front seat backward and seat cushion fully upward

   

4. Open hood
   Note

   Using MCU touchscreen > Controls > Frunk Trunk

   

   

5. Remove rear underhood apron
   Note

   8x clips

   

   

6. Remove RH underhood apron
   Note

   9x clips

   

   

7. Remove LH underhood apron
   Note

   9x clips

   

   

8. Release drainage hoses from HEPA filter inlet duct
   Note

   2x hoses

   

   

9. Remove clips securing HEPA filter inlet duct to cowl panel
   Note

   3x push clips

   

10. Remove HEPA filter inlet duct
    Note

    2x clips on HEPA filter

    

    

11. Remove HEPA filter outlet duct from vehicle
    Note

    Lift up, pull towards front of vehicle, then rotate clockwise

    

    

12. Power down vehicle using MCU
    Note

    Controls > E-brake & Power Off > Power off

    

    

13. Disconnect 12V negative terminal and First Responder Loop
    Note

    1x nut, 10mm, 5 Nm, 1x connector, Wait at least 2 minutes before disconnecting modules or HV components

    

14. Disconnect controller connectors underneath LH front seat
    Note

    5x connectors, 1x harness clip

    

    

15. Remove LH front seat controller
    Note

    3x clips

    

    

    

    

16. Install LH front seat controller
    Note

    3x clips, Install the rear seat controller clip first and then install the front two clips

    

    

    

    

17. Install connectors to LH front seat controller
    Note

    5x connectors, 1x harness clip

    

    

18. Connect First Responder Loop and 12V negative terminal
    Note

    1x nut, 10mm, 5 Nm, 1x connector

    

19. Install HEPA filter outlet duct

    

    

20. Install HEPA filter inlet duct
    Note

    2x tabs, One on each side

    

    

21. Install clips securing HEPA filter inlet duct to cowl panel
    Note

    3x push clips

    

22. Secure drainage hoses to HEPA filter inlet duct
    Note

    2x hoses

    

    

23. Install LH underhood apron
    Note

    9x clips

    

    

24. Install RH underhood apron
    Note

    9x clips

    

    

25. Install rear underhood apron
    Note

    8x clips

    

    

26. Close hood
    Note

    Press firmly in green highlighted areas (see image), Damage may result from pressure elsewhere on hood

    

27. Move LH front seat to original position

    

28. Using Laptop connect to vehicle with a tethered Ethernet connection via Toolbox 3.0
    Note

    1x connector, Open Toolbox 3 website and establish connection to the vehicle. Select connection status icon at top right corner, and select Connect Locally (icon will turn green when vehicle is connected)

    

    

29. Select "Actions/Autodiag" and search for "Service_Redeploy"
30. Select UPDATE_CAN-REDEPLOYvia Toolbox: (link)via Service Mode Plus:
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1L Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE1R Replacement ➜ CAN Redeploy
    • Drive Inverter Replacement ➜ Drive Inverter DIRE2 Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Front Drive Unit Replacement ➜ CAN Redeploy
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ CAN Redeploy
    , click "Run", and allow routine to complete
    Note

    Select "X" at top right of window to close once complete
31. Select proper garage type for vehicle
    Note

    prod, eng, or mfg, Redeploy should start even though Error may be displayed
32. Close redeploy window
    Note

    Select X at top right corner of window
33. Select the clock on the center display, then select install now to start firmware update
    Note

    Tap center display next to software update window until clock runs down to 0. After displayed installation time, Check the center display and ensure the firmware package was successfully installed
34. Place vehicle in service mode with touchscreen
    Note

    Hold Tesla "T" icon at top of center display for four seconds and then type "service" into dialog box
35. Precondition vehicle to 68F
    Note

    Must be preconditioned for 10 minutes before calibration is performed

    

36. Set driver seat heater to level 1
    Note

    driver seat must have seat heater turned on to level 1 before any calibration is performed

    

37. To run routine successfully, apply foot to brake pedal and hold right turn signal indicator for 10 plus seconds
    Note

    This step is required even when using a tethered Ethernet connection. Routine can be run after the 10 seconds expire, Key fob must be present in vehicle

    

    

38. Type TEST-SELF_VCSEATD_FRONT_SEATvia Toolbox: (link) in the search field and then Run
    Note

    Make sure "Actions" is selected if not already, Ensure nothing is sitting on the driver seat
39. Type PROC_VCSEATD_SEAT-CALIBRATEvia Toolbox: (link) in the search field and then Run
    Note

    Make sure "Actions" is selected if not already, Ensure nothing is sitting on the driver seat
40. Disconnect Toolbox from vehicle and install cubby under the MCU
    Note

    1x connector, 2x clips

    

    

41. Exit Service Mode
    Note

    Hold Tesla T icon at top of center display for four seconds and then type "service" into dialog box

    

42. Raise LH front window

    

43. Close LH front door