2026-11-13

空调压缩机(Model Y L) ((拆卸和更换))

校正代码 18200600402 FRT 1.38 注意:除非本程序中另有明确规定,否则上文所列校正代码及相关 FRT 反映的是执行本程序(包括关联程序)所需的所有工作。除非明确要求,否则请勿堆叠校正代码。 注意:请参阅平均维修工时深入了解 FRT 及其创建方式。 注意:请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意:请参阅人体工程学注意事项查看安全健康的作业规程。

警告
本程序为“草案”。虽已通过验证,但可能仍有“警告”和“注意”事项缺失。请遵守安全要求,处理或靠近高压系统和部件时,请谨慎操作。
  • 2026-10-30: Released new procedure.
警告

只有完成全部所需认证的技术人员才能执行此程序。Tesla 特斯拉建议第三方服务提供商技术人员在执行此程序之前接受同等培训。有关 Tesla 技术人员要求的更多信息,或第三方主题说明,请参阅高压认证要求。处理高压线缆、母排或接头时,务必全程穿戴最低防护等级为 0(1000V) 的适当个人防护装备 (PPE)及高压绝缘手套。有关其他安全信息,请参阅技术注意事项 TN-15-92-003,高压安全意识注意事项。

警告
Thermal management components operate under very tight specifications and can malfunction if Service procedures are not carefully followed. DO NOT rely on past experience with other thermal management systems; read through the Service Manual and do not deviate from the instructions.
警告
The desiccant bag in the receiver dryer must be checked when replacing the A/C compressor to determine if debris resulting from failure of the compressor has entered the system.
注
此程序要求执行空调制冷剂(回收和重新加注)程序。如果尚未自动添加到“服务工单”中,请将校正代码 18200102 作为同一工项下的一个单独校正程序添加至“服务工单”中。

拆卸

  1. Set up the A/C machine.
    注
    Touch time only. Connect to power. Turn power switch on.
  2. Raise and support vehicle. See 举升车辆 - 双柱举升机.
  3. Open the LH front door and lower the LH front window.
  4. Enable Service Mode. See 维护模式.
  5. Unlock the vehicle gateway. See 网关(解锁).
  6. On the touchscreen, touch the Service Mode "wrench" (at the bottom of the touchscreen UI), and then touch Thermal > Refrigerant System > Start Refrigerant Fill/Drain > Run, and allow the routine to complete.
    注
    Thermal Fill Drain routine has a 5 hour time limit. If the run time exceeds 5 hours, the routine must be performed again.
  7. Remove the HEPA filter assembly. See 滤清器总成 - HEPA ((拆卸和更换)).
  8. Remove the underhood storage unit. See 前备箱储物单元(拆卸和更换).
  9. Recover the A/C refrigerant. See 空调制冷剂 (如有需要 - 添加制冷剂)(回收和加注) (Restore).
  10. Disconnect the LV battery. See 低压电源(断开和连接) (Modify).
  11. Perform Vehicle HV Disablement Procedure. See 车辆高压禁用程序.
  12. Remove the LV battery. See 16V 锂离子电池 ((拆卸和安装)).
  13. Release the connector locking tab, and then disconnect the HVIL connector near the LH front strut tower.
    注
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
    提示
    推荐使用以下工具
    • 小型软握尖凿,90 度尖嘴,6 英寸
  14. Release the connector locking tab, then disconnect the A/C logic electrical connector from the A/C compressor.
    注
    DO NOT push down on the red locking tab. Pull the tab away from the connector until the connector is unlocked, and then continue pulling to release the connector.
    提示
    推荐使用以下工具
    • 小型软握尖凿,90 度尖嘴,6 英寸
  15. Use a clip pry tool to release the retaining clip that attaches the A/C compressor logic harness to the A/C compressor HV harness bracket.
  16. Inspect and put on HV insulating gloves and leather over gloves.
  17. Remove the bolt that attaches the A/C compressor HV harness bracket to the A/C compressor.
    提示
    推荐使用以下工具
    • 13 mm 套筒
  18. Disconnect the HV harness electrical connector from the A/C compressor.
    提示
    推荐使用以下工具
    • Small flat head screwdriver
  19. Release the tab that attaches the HV harness to the A/C compressor, and set it aside.
  20. Remove leather over gloves and HV insulating gloves.
  21. Remove the bolt that attaches the ground strap to the A/C compressor, and then set the ground strap aside.
    提示
    推荐使用以下工具
    • T25 梅花套筒
  22. Use a clip pry tool to release the clip that attaches the coolant hose to the A/C compressor bracket.
  23. Use a clip pry tool to release the clips (x4) that attach the coolant hose to the A/C compressor bracket.
  24. Remove the nut that attaches the low pressure fitting to the compressor, then move the line aside for clearance.
    注
    推荐使用以下工具
    • 13 mm 套筒
  25. Remove the nut that attaches the high pressure fitting to the compressor, then move the line aside for clearance.
    注
    推荐使用以下工具
    • 13 mm 套筒
  26. Seal the low pressure and high pressure opening ports on the A/C compressor with masking tape to prevent debris from entering and oil leakage.
  27. With an assistant, remove the bolts (x2) that attach the A/C compressor assembly to the strut tower brace, and then carefully maneuver the assembly towards the front of the vehicle, under the strut tower support brace.
    提示
    推荐使用以下工具
    • 15 毫米套筒
  28. Remove the bolts (x3) that attach the A/C compressor bracket to the A/C compressor.
    注
    Use of the following tool(s) is recommended:
    • 10 mm socket
  29. Release the buttons that attach the NVH acoustic cover to the compressor, and then remove the cover from the compressor.
    注
    The acoustic cover can be reused if not damaged.
  30. Install the A/C flush adapters onto the supermanifold to compressor A/C line assembly.
    注
    2x nuts, 13mm, 22 Nm. Install flush adapters onto suction and discharge lines on the compressor side. Leave seal washers on A/C manifold line. Use 13mm nuts from compressor to secure flush adapters.
  31. Connect A/C machine hoses to A/C flush adapters.
  32. On the A/C machine touchscreen, select Menu > Flushing Kit, and enter 25 mins vacuum time. Follow the machine guide to start the flush, and then allow the process to complete.
    注
    A minimum of 3200 g of refrigerant is needed in the tank to run the system flush procedure. System flush procedure runs for approximately 90 minutes.
  33. Disconnect the A/C machine hoses from the A/C flush adapters.
  34. Remove the nuts (x2) that secure the A/C flush adapters and remove the adapters.
    注
    Use of the following tool(s) is recommended:
    • 3 in extension
    • 13 mm socket
    • Cordless 3/8in Dr Impact
  35. Remove the underhood storage unit reinforcement beam from the vehicle. See 梁 - 加固 - 前备箱(拆卸和更换).
    注
    No need to remove the cooling fan isolation brackets.
  36. Remove the desiccant filter. See 干燥剂(Model Y L) ((拆卸和更换)).

安装

  1. Install the desiccant filter. See 干燥剂(Model Y L) ((拆卸和更换)).
  2. Install the underhood storage unit reinforcement beam. See 梁 - 加固 - 前备箱(拆卸和更换).
  3. Confirm part numbers of new and old compressors to update the configuration in later steps.
    注
    Refer to article https://toolbox.teslamotors.com/articles/5696900 for compressor configuration.
  4. Install the NVH acoustic cover to the compressor.
    注
    Acoustic cover can be reused if not damaged.
  5. Install the buttons (x8) that secure the acoustic cover to the compressor.
  6. Install the bolts (x3) that attach the A/C compressor bracket to the A/C compressor.
    9 Nm (6.6 lbs-ft)
    注
    Use of the following tool(s) is recommended:
    • 10 mm socket
  7. With an assistant supporting the A/C compressor assembly under the strut tower brace, hand-start the bolts (x2) that attach the A/C compressor assembly to the brace, and then torque the bolts.
    31 Nm (22.9 lbs-ft)
    提示
    推荐使用以下工具
    • 15 毫米套筒
  8. Remove the bolts and covers from the low pressure and high pressure opening ports on the new compressor.
    注
    2x plugs, 2xbolts, 13mm
  9. Replace the O-rings on the high pressure and low pressure supermanifold to A/C compressor hose fittings.
    注
    O-ring for high pressure line: 1111738-00-A WASHER, 1/2,STL ZN, SEAL.
    注
    O-ring for low pressure line: 1111740-00-A WASHER, 3/4,STL ZN, SEAL.
    注
    Lubricate O-rings with ND-11 oil prior to installation.
  10. Position the supermanifold to A/C compressor high pressure fitting on the A/C compressor, and then install the nut that attaches the fitting to the A/C compressor.
    22 Nm (16.2 lbs-ft)
    注
    推荐使用以下工具
    • 13 mm 套筒
  11. Position the supermanifold to A/C compressor low pressure fitting on the A/C compressor, and then install the nut that attaches the fitting to the A/C compressor.
    22 Nm (16.2 lbs-ft)
    注
    推荐使用以下工具
    • 13 mm 套筒
  12. Install the clips (x4) that secure the coolant hose to the A/C compressor bracket.
    \
  13. Install the clip that secure the radiator inlet hose to the A/C compressor bracket.
  14. Position the ground strap on the A/C compressor, and then install the bolt that attaches the ground strap to the A/C compressor.
    6 Nm (4.4 lbs-ft)
    提示
    推荐使用以下工具
    • Torx T25 socket
  15. Inspect and put on HV insulating gloves and leather over gloves.
    注
    Use HV cut resistant insulated gloves or HV insulating gloves and leather over gloves. HV Insulating gloves must be worn any time a Hioki Tester or Hi-Pot Tester is used. Refer to service document TN-15-92-003 R5 for PPE requirements depending on vehicle configuration.
  16. Install the tab that attaches the HV harness to the A/C compressor.
  17. Connect the HV harness electrical connector to the A/C compressor.
  18. Install the bolt that attach the A/C compressor HV harness bracket to the A/C compressor.
    22 Nm (16.2 lbs-ft)
    注
    Use of the following tool(s) is recommended:
    • 13 mm socket
  19. Remove leather over gloves and HV insulating gloves.
  20. Install the clip securing harness to HV harness bracket.
  21. Connect the A/C compressor logic connector and engage the locking tab.
  22. Connect the HVIL connector and engage the locking tab.
  23. Reconnect A/C machine hoses to vehicle
  24. Perform the vacuum leak test and recharge the refrigerant. See 空调制冷剂 (如有需要 - 添加制冷剂)(回收和加注) (Restore).
  25. Install the LV battery. See 16V 锂离子电池 ((拆卸和安装)).
  26. Connect LV power. See 低压电源(断开和连接) (Modify).
  27. Connect a low-voltage battery maintainer. See 低压维护器(连接和断开) (Maintenance).
  28. Connect a laptop with Toolbox to the vehicle. See Toolbox(连接和断开).
  29. On the vehicle touchscreen, touch Thermal > Refrigerant System > Stop Refrigerant Fill/Drain > Run, and allow the routine to complete.
  30. Set the compressor Type using the touchscreen:
    • For vehicles that run firmware version 2026.2.3 or later (NA/EMEA) or 2025.44.32 or later (APAC), touch Thermal > Actions > Configure Compressor, and then touch Run to start the routine.
    • For vehicles that run earlier firmware versions, touch Thermal > Actions > Thermal Configurations > compressorType, and then select and save the correct compressor type
    注
    In case the routine did not complete successfully, refer to Toolbox article 5696900 for compressor configuration.
    注
    Check the Gateway configuration for compressorType and make sure it shows as intended.
  31. Reinstall the software. See 软件重新安装 - 触摸屏.
  32. Remove the LV maintainer. See 低压维护器(连接和断开) (Maintenance).
  33. 运行 ODIN 例行程序: PROC_VCFRONT_X_RESET-COMPRESSOR-P-METRICvia Service Mode:Thermal ➜ Refrigerant System ➜ Reset Compressor P-Metricvia Toolbox:(link)
  34. 运行 ODIN 例行程序: TEST-SELF_VCFRONT_X_HEAT-PUMP-COMMISSIONINGvia Service Mode:Thermal ➜ Refrigerant System ➜ Commission Heat Pumpvia Service Mode Plus:Drive Inverter ➜ Front Drive Inverter Replacement ➜ Heatpump commissioningvia Toolbox:(link)
  35. 运行 ODIN 例行程序: TEST-SELF_VCFRONT_X_THERMAL-PERFORMANCEvia Service Mode:Thermal ➜ Actions ➜ Test Thermal Performancevia Service Mode Plus:
    • Drive Inverter ➜ Front Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Left Drive Inverter Replacement ➜ Thermal System Test
    • Drive Inverter ➜ Rear Right Drive Inverter Replacement ➜ Thermal System Test
    • Drive Unit ➜ Front Drive Unit Replacement ➜ Thermal System Test
    • Drive Unit ➜ Rear Drive Unit Replacement ➜ Thermal System Test
    via Toolbox:(link)
  36. Remove the laptop from the vehicle.
  37. Exit Service Mode Plus. See 维护模式增强版.
  38. Install the HEPA filter assembly. See 滤清器总成 - HEPA ((拆卸和更换)).
  39. Install the underhood storage unit. See 前备箱储物单元(拆卸和更换).
  40. Raise the LH front window and close the LH front door.