Current Release Notes

Archived Release Notes:

Week Ending September 14, 2024

The following new procedure(s) were added:

The following procedure(s) were updated:

Air Spring Module - Rear - LH (Remove and Replace) - Added image to depict setting vehicle suspension to ride height.
Fusebox - Underhood - 2nd Generation (Remove and Replace) - Added reference to rework of fuse box, if needed.
Media Control Unit (Remove and Replace) - Added owner authorization request.
Receiver Dryer and Desiccant (Remove and Replace) - Added warnings to wear suitable protective clothing, consisting of face and eye protection, heat-proof gloves, rubber boots and apron or waterproof overalls must be worn when carrying out operations on the air conditioning system.

The following new procedure(s) were added:

The following procedure(s) were updated:

Clear Forward Camera View (Precision Cleaning Of Inboard Windshield) - Added a step to clean the wiper blades.
Tesla Badge - Rear (Remove and Replace) - Added a note to remind that the rear badge is not reusable due to the positioning problem.
Wheel (Remove and Replace) - Added instruction for wheel disposal.

The following procedure(s) were updated:

Air Spring Module - Front - LH (Remove and Replace) - Added note to perform air dryer regeneration when replacing component because of a leak.
Air Spring Module - Rear - LH (Remove and Replace) - Added note to perform air dryer regeneration when replacing component because of a leak.
HV Battery (RWD/AWD) (Remove and Install) - Added note stating it is not necessary to perform HV disablement.
HV Battery (RWD/AWD) (Remove and Replace) - Added note stating it is not necessary to perform HV disablement.

The following procedure(s) were updated:

Adaptive Air Spring Module - Front - LH (Remove and Replace) - Added note to perform air dryer regeneration when replacing component because of a leak.
HV/LV Ancillary Unit (HV Battery 2.0) (Remove and Replace) - Added Pack Contactor Replacement routine for vehicles with Tegra MCU.

The following new procedure(s) were added:

The following procedure(s) were updated:

DCDC Converter - 2nd Generation (Retrofit) - Updated instructions for cable markings.
Vehicle Sanitation - Evaporator - Tunap 994 (EMEA) - Removed sub-procedures for sanitation using Tunap 589 and Tunap I880.
Vehicle Sanitation - Interior Air - Tunap 589 (EMEA) - Removed sub-procedures for sanitation using Tunap 996 and Tunap I880.

The following procedure(s) were updated:

HV/LV Ancillary Unit (HV Battery 2.0) (Remove and Replace) - Swapped illustrations in steps for Hioki measurement on positive and negative terminals.

The following procedure(s) were updated:

Contactors - HV Battery (HV Battery 1.0/1.5) (Remove and Replace) - Changed tool part number from 1046409-00-B – TIP, CONTACTOR-BUSBAR, L-SHAPED to 1046409-00-A – TIP, CONTACTOR-BUSBAR, L-SHAPED, REV 02.
Fuse Locations - Update the link of Electrical Information.
Sensor - Ride Height - Front - LH (Retrofit) - Added note on front sensor mounting bracket.
Sensor - Ride Height - Front - LH (Remove and Replace) - Added note on front sensor mounting bracket.
Sensor - Ride Height - Rear - LH (Remove and Replace) - Added note on rear sensor mounting bracket.

The following procedure(s) were updated:

Contactors - HV Battery (HV Battery 1.0/1.5) (Remove and Replace) - Added tool info for 1046409-00-B – TIP, CONTACTOR-BUSBAR, L-SHAPED.

The following new procedure(s) were added:

The following procedure(s) were updated:

BMS PCBA - High Voltage Battery Assembly (HV Battery 2.0) (Remove & Replace) - Swapped illustrations in steps for Hioki measurement on positive and negative terminals, added torque figure to Installtion step 1 for BMS PCBA board.

The following procedure(s) were updated: