2026-11-12

制动盘 - 前 - 左侧(拆卸和更换)

校正代码 33010102 0.24 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See 人员保护 to make sure wearing proper PPE when performing the below procedure. NOTE: See for safe and healthy working practices.

Equipment:
  • 1134786-00-A 制动钳扩张器工具,Model 3
  • 2026-11-09: Added Note on cleaning the hub face of any corrosion/debris prior to installing the new brake rotor.
  • 2025-05-08: Updated brake pad burnishing step to be performed after rotor replacement.
  • 2023-11-22: Added extra information for single rotor replacement.
Note
For detailed brake specifications, see .
Note
If only a single rotor needs replacing (due to damage), the corresponding axle rotor must be measured for runout and thickness. See .

扭矩规格

Table 1. 扭矩规格: 制动盘 - 前 - 左侧(拆卸和更换)
描述 扭矩值 推荐工具 重复使用/更换 备注
LH front brake hose bracket to the LH front knuckle
5 Nm (3.7 lbs-ft)
  • 10 毫米套筒扳手
重复使用
LH front caliper to the LH front knuckle
94 Nm (69.3 lbs-ft)
  • 外梅花套筒 E18
更换 1088969-00-B
Brake rotor to the hub
5 Nm (3.7 lbs-ft)
  • 10 毫米套筒扳手
重复使用

拆卸

  1. Raise the vehicle and remove the front LH wheel. See 轮毂(拆卸和安装).
  2. Remove the bolt that attaches the LH front brake hose bracket to the LH front knuckle.
    5 Nm (3.7 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手
  3. Remove and discard the bolts that attach the LH front caliper to the LH front knuckle, remove the caliper from the knuckle, and allow the caliper to hang from an S-hook.
    94 Nm (69.3 lbs-ft)
    CAUTION
    Make sure the brake caliper and hoses are not twisted when hanging the caliper or during reinstallation, as this can damage the brake hose.
    Tip
    推荐使用以下工具
    • 外梅花套筒 E18
    Note
    If needed, use the caliper spreader tool to push the caliper pistons to the fully open position.
  4. Remove the bolt that attaches the brake rotor to the hub, and then remove the brake rotor from the hub.
    5 Nm (3.7 lbs-ft)
    Tip
    推荐使用以下工具
    • 10 毫米套筒扳手

安装

安装程序与拆卸程序相反,以下各项除外:

  1. Prior to installing the new brake rotor, clean the hub face of any corrosion/debris present on the hub face.
  2. Replace patchbolts.
  3. 紧固后,使用油性记号笔标记紧固件。
  4. Press the brake pedal at least 5 times to seat the pads against the rotor.
    Warning
    Always check that the brake pads are seated correctly before driving the vehicle.
  5. Burnish the brakes. See .
    Note
    During vehicle driving, make sure that proper brake pedal feel and performance is achieved.
    Note
    Add the correction code for brake pad burnishing 33013000 as a separate correction within the same activity to the Service Visit.