2026-08-10

Hinge Pillar Inner

Correction code: 10100127502 10100127602 NOTE: Unless explicitly stated in the procedure, the above correction code includes all Collision Repair and Service repair work required to perform this procedure, including the linked Collision Repair procedures and linked Service procedures. Do not stack Collision Repair correction codes unless explicitly told to do so. Depending on the damage to the vehicle, additional repairs may be required.

Parts List

Quantity Description Image / Notes
1 ASY, HINGE PILLAR INR (Hinge Pillar Inner)
8 Structural Rivet, 6.5 mm Medium
1 SPR, 5x4.5
2 SPR, 5x7
1

Bolt, hex-head , M6x1.00x18

Tesla part number 1006529-00-A.

When ordering parts, refer to the Parts Catalog and enter the VIN of the vehicle being repaired to find the correct parts (and the part numbers) for the vehicle. Alternatively, use the search function in the Parts Catalog to find a specific part for the vehicle.

Repair Procedure

  1. Remove the Door Assembly - Front - LH (Remove and Install).
  2. Remove the Applique - Front Quarter - LH (Remove and Replace).
  3. Remove the Hood Assembly (Remove and Install).
  4. Remove the Fender Assembly - Front - LH (Remove and Replace).
  5. Remove the Wheel Arch Liner - Front - LH (Remove and Replace).
  6. Remove the Carrier - Rocker Panel - LH (Remove and Replace).
  7. Remove the Seal - Primary - Front Door - LH (Remove and Replace).
  8. Remove the Applique - Roof - Front (Remove and Replace).
  9. Remove the Assembly - Mesh Grille - Defrost (Remove and Replace).
  10. Remove the Hinge - Door - Front - Lower - LH (Remove & Replace).
  11. Remove the Hinge - Door - Front - Upper - LH (Remove & Replace).
  12. Remove the Carpet - 1st Row (Remove and Replace).
  13. Remove the A-Pillar Reinforcement Assembly.
  14. Remove the A-Pillar Upper Outer Lower Bracket.
  15. Remove the A-Pillar Reinforcement Assembly.
  16. Remove the Hinge Pillar Reinforcement.
  17. Remove the A-Pillar Upper Outer Lower Bracket.
  18. Remove the original component.
    or Factory Spot Welds

    or Bolts, hex-head

  19. Prepare for installation.

    or Structural Rivets, 6.5 mm Medium

    or SPRs, 5x4.5
    Note
    The following Tesla SPR die is required to install this SPR: SM 085 0125.
    or SPRs, 5x7
    Note
    The following Tesla SPR die is required to install this SPR: SM 085 0125.

    or Bolts, hex-head

  20. Apply structural adhesive to the mating surfaces on the vehicle and the new component or components.
  21. Position the new component and temporarily install the bolts as shown to secure the component in position while the structural adhesive cures.
    Note
    Remove the bolts after the structural adhesive has cured.
  22. Install the new component or components.
    Torque the bolt to 10 Nm.
  23. Install the Hinge Pillar Reinforcement.
  24. Install the A-Pillar Reinforcement Assembly.
  25. Install the A-Pillar Upper Outer Lower Bracket.
  26. Perform any necessary post-repair operations.
  27. Install the A-Pillar Upper Outer Lower Bracket.
  28. Install the A-Pillar Reinforcement Assembly.
  29. Install the Carpet - 1st Row (Remove and Replace).
  30. Install the Hinge - Door - Front - Upper - LH (Remove & Replace).
  31. Install the Hinge - Door - Front - Lower - LH (Remove & Replace).
  32. Install the Assembly - Mesh Grille - Defrost (Remove and Replace).
  33. Install the Applique - Roof - Front (Remove and Replace).
  34. Install the Seal - Primary - Front Door - LH (Remove and Replace).
  35. Install the Carrier - Rocker Panel - LH (Remove and Replace).
  36. Install the Wheel Arch Liner - Front - LH (Remove and Replace).
  37. Install the Fender Assembly - Front - LH (Remove and Replace).
  38. Install the Hood Assembly (Remove and Install).
  39. Install the Applique - Front Quarter - LH (Remove and Replace).
  40. Install the Door Assembly - Front - LH (Remove and Install).