2026-08-09

MXP3 Body - Bumper and Fascia - Front Grille and Applique - T Badge Carrier (2025+) (RR)

校正代码 NEW 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。
  • 2025-06-02: Released new procedure.
  1. Open the LH front door.
  2. Lower both front windows.
  3. Press brake pedal to turn on drive rails
  4. Set air suspension ride height to “Very High”
    注
    Via center display > Controls > Suspension > ''Very High''
  5. Turn steering wheel fully to right
  6. Open the hood.
  7. Remove the rear underhood apron.
  8. Remove the LH underhood apron.
  9. Remove the RH underhood apron.
  10. Remove the front underhood apron.
  11. Remove bolts securing upper portion of front fascia
    注
    6x bolts, 10mm, 7 Nm
  12. Remove fasteners securing LH front wheel liner to valence
    注
    1x bolt, T30, 1.5 Nm, 3x clips, Move front portion of wheel liner backwards to access fairing
  13. Remove LH front wheel fairing from valence
    注
    2x bolts, 10mm, 1.5 Nm, 1x securing tab
  14. Partially remove front portion of LH front fender garnish
    注
    2x clips, 8x tabs, Careful to not damage dummy ultra sonic sensor when removing garnish
  15. Remove bolt securing LH front of fascia to LH front fender
    注
    1x bolt, 8mm, 1.5 Nm
  16. Disconnect fascia camera hose from washer pump
    注
    1x hose, Release locking tab to disconnect washer hose
  17. Press brake pedal to turn on drive rails
  18. Turn steering wheel fully to left
  19. Remove clips securing RH front wheel liner to valence
    注
    4x clips, Move front portion of wheel liner backwards to access fairing
  20. Remove RH front wheel fairing from valence
    注
    2x bolts, 10mm, 1.5 Nm, 1x securing tab
  21. Partially remove front portion of RH front fender garnish
    注
    2x clips, 8x tabs, Careful to not damage dummy ultra sonic sensor when removing garnish
  22. Remove bolt securing RH front of fascia to RH front fender
    注
    1x bolt, 8mm, 1.5 Nm
  23. Power off the vehicle using the touchscreen.
  24. Disconnect the LV battery connector and First Responder Loop.
  25. Disconnect front fascia assembly
    注
    2x connectors, Release locking tabs then disconnect, 1x nano nozzle
  26. Remove fasteners securing lower portion of front fascia to valence
    注
    3x bolts, 10mm, 3 Nm, 2x clips
  27. Apply masking tape to protect LH and RH front fenders
  28. Remove front fascia assembly from vehicle
    注
    Recommend assistance, Release fascia from LH and RH fender brackets, Careful not to damage the fender bracket when removing fascia, Place on protected surface to avoid damage
  29. Disconnect front BLE
    注
    1x connector, Do not push down on red tab, Pull red tab to disengage lock, Pull again to release connector
  30. Remove T badge carrier from front fascia
    注
    1x screw, T25, 3 Nm, 6x tabs
  31. Release front fascia V bar from front T badge carrier
    注
    4x clips
  32. Remove front BLE from front T badge carrier
    注
    2x screws, T25, 3 Nm
  33. Remove T badge from T badge carrier
    注
    2 screws, T25, 1.8 Nm
  34. Install T badge onto T badge carrier
    注
    2 screws, T25, 1.8 Nm
  35. Install front BLE onto T badge carrier
    注
    2 screws, T25, 3 Nm
  36. Install front fascia V bar onto T badge carrier
    注
    4x clips
  37. Install screws securing front fascia V bar onto T badge carrier
    注
    1x screw, T25, 3 Nm
  38. Install T badge carrier onto front fascia assembly
    注
    1x screw, T25, 3 Nm, 6x Tabs
  39. Install T badge carrier onto front fascia assembly
    注
    1x screw, T25, 3 Nm, 6x Tabs
  40. Connect front BLE
    注
    1x connector, Engage locking tab
  41. Install front fascia onto vehicle
    注
    Recommend assistance, Slide LH and RH side of fascia into fenders, Careful not to damage the fender bracket when installing fascia
  42. Remove masking tape from front fenders
  43. Install bolt securing fascia to RH fender bracket
    注
    1x bolt, 8mm, 5 Nm
  44. Connect front fascia harness onto frunk harness
    注
    2x connectors, Engage locking tab, Located behind RH wheel arch liner
  45. Install RH front fender garnish
    注
    2x clips, 8x tabs, Secure from top to bottom of front bumper
  46. Install RH front wheel fairing to valence
    注
    2x bolts, 10mm, 1.5 Nm
  47. Install push clips securing RH front wheel liner onto fascia
    注
    4x clips
  48. Connect the First Responder Loop and LV battery connector.
  49. Press brake pedal to turn on drive rails
  50. Turn steering wheel fully to right
  51. Connect fascia camera hose to washer pump
    注
    1x hose, Secure locking tab
  52. Install bolt securing fascia onto LH fender bracket
    注
    1x bolt, 8mm, 5 Nm
  53. Install LH front fender garnish
    注
    2x clips, 8x tabs, Secure from top to bottom of front bumper
  54. Install LH front wheel fairing to valence
    注
    2x bolts, 10mm, 1.5 Nm, 1x securing tab
  55. Install fasteners securing LH front wheel liner to valence
    注
    1x bolt, T30, 1.5 Nm, 3x clips
  56. Install fasteners securing lower portion of front fascia to valence
    注
    3x bolts, 10mm, 3 Nm, 2x clips
  57. Install bolts securing upper portion of front fascia
    注
    4x bolts, 10mm, 7 Nm, Ensure proper fascia-to-headlamp gap and flushness
  58. Install the front underhood apron.
  59. Install the LH underhood apron.
  60. Install the RH underhood apron.
  61. Install the rear underhood apron.
  62. Close the hood.
  63. Calibrate the RH falcon wing door.
  64. Calibrate the LH falcon wing door.
  65. Press brake pedal to turn on drive rails
  66. Turn steering wheel back to center
  67. Set air suspension ride height to Medium
    注
    Using center display > Suspension > Medium/Standard
  68. Raise both front windows.
  69. Close the LH front door.