2026-09-29

同轴电缆 – 侧转向灯 - 前 - 右（更换） ((拆卸和更换))

校正代码 17403112 FRT 2.82 注意：除非本程序中另有明确规定，否则上文所列校正代码及相关 FRT 反映的是执行本程序（包括关联程序）所需的所有工作。除非明确要求，否则请勿堆叠校正代码。 注意：请参阅平均维修工时深入了解 FRT 及其创建方式。 注意：请参阅人员保护确保在执行以下程序时穿戴适当的个人防护装备 (PPE)。 注意：请参阅人体工程学注意事项查看安全健康的作业规程。

警告
本程序为“草案”。虽已通过验证，但可能仍有“警告”和“注意”事项缺失。请遵守安全要求，处理或靠近高压系统和部件时，请谨慎操作。
  • 2026-07-09: Released new procedure.

Overlay

  1. Open both front doors and lower both front windows.
  2. Remove the underhood storage unit. See 前备箱储物单元（拆卸和安装）.
  3. Remove the wiper module. See 雨刮器模块（拆卸和更换）.
  4. Move the RH front seat backward.
  5. Remove RH front floor mat
  6. Remove RH footwell cover
    注
    3x magnets, 1x connector, 4x datums
  7. Remove RH console side carpet
    注
    11x clips, 2x datums
  8. Remove RH front door sill trim panel
    注
    8x clips, 3x datums, Partially release seal if needed
  9. Remove RH IP end cap
    注
    3x clips
  10. Remove RH mid A-pillar trim
    注
    2x clips, 3x datums, Release clips from upper A-pillar and IP sub assembly, Lift mid A-pillar trim out of lower A-pillar trim
  11. Remove RH lower A-pillar trim
    注
    1x bolt, T25, 5 Nm, 2x clips, 1x datum
  12. Fold RH front cabin carpet aside for access
  13. Release harness from RH footrest panel
    注
    1x clip
  14. Release RH footrest panel
    注
    2x bolts, 10mm, 5 Nm, 2x nuts, 10mm, 5 Nm
  15. Remove RH footrest panel
    注
    Fold RH primary support carpet up, Rotate RH footrest panel out of vehicle
  16. Disconnect side repeater cameras connector X870 at car computer
    注
    1x connector, Release red tab then disconnect
  17. Raise and support the vehicle.
  18. Remove RH front wheel center cap
    注
    1x cap
  19. Loosen RH front wheel
    注
    5x nuts, 21mm, 175 Nm
  20. Raise vehicle partially and lower onto locks
    注
    Set vehicle to comfortable working height, Make sure there's an audible click of the locks on both sides before lowering, otherwise vehicle may tilt to the side
  21. Remove RH front wheel
    注
    5x nuts, 21mm, 175 Nm
  22. Release rear portion of RH front fender garnish
    注
    3x clips, 2x tabs, Starting from the rear release garnish to access rocker
  23. Remove rear portion of RH front wheel liner
    注
    7x clips, 1x fan clip, Carefully rest rear portion of wheel line on brake rotor
  24. Disconnect RH front repeater
    注
    2x connectors
  25. Release RH grommet from body
    注
    With a razor blade, carefully cut the electrical tape away exposing the rubber dust boot
  26. Remove electrical tape securing harness bundle to rubber dust boot
  27. Release the terminal 2 lock on the double connector side of coax overlay cable
    注
    Using the pin drag kit, carefully lift the hold down tab
  28. Remove the double connector from the overlay coax cable
    注
    Using the pin drag kit, pull the coax away from the connector
  29. Wrap the overlay coax cable with harness tape before installation
    注
    Use Anti-abrasion tape and wrap the entire length of the coax cable to protect the cable for damage when it is installed the vehicle
  30. Feed the previously removed coax terminal through the RH wheel liner and dust boot towards the interior cabin
    注
    Once the coax is exposed on the other side of the dust boot carefully pull till you have roughly 12 inches of cable towards the interior of the vehicle
  31. Pull the RH coax over through the bulkhead and into the interior cabin
    注
    Pull harness toward car behind car computer
  32. Overlay the RH coax wire onto the harness and secure it to the car computer harness
    注
    3x zip-ties, Trim off excess material after harness has been secured
  33. Secure coax overlay through RH wheel liner and frunk harness
    注
    4x zip-ties, Trim off excess material after harness has been secured
  34. Depin the LH side coax cable (Terminal 2) from the connector X820
    注
    Verify that you are removing the correct side (1 & 2, where 1 is the LH repeater and 2 is the RH repeater) Using MDLS drag pin tool set carefully lift the purple locking tab up and out of the connector housing
  35. Remove the coax cable from the connector X820
    注
    Using the pin drag kit, carefully lift the hold down tab an simultaneously pull the coax away from the connector
  36. Insert the connector locking tab and reconnect X820 together
    注
    1x connector
  37. Secure side repeater cameras connector X870 onto car computer
    注
    1x connector
  38. Cut off the vehicle side repeater coax terminal and tape to vehicle harness
    注
    Cut the coax connector only
  39. Connect RH front repeater
    注
    2x connectors, Support repeater from exterior to prevent damage to retaining clips
  40. Secure RH grommet onto body
    注
    Use electrical tape to wrap the end of the dust boot
  41. Secure rear portion of RH front wheel liner
    注
    4x clips
  42. Secure rear portion of RH front fender garnish
    注
    3x clips, 2x tabs, Fully secure and carefully engage clips
  43. Install RH front wheel
    注
    5x nuts, 21mm, 175 Nm, Start lug nuts by hand before using power tool
  44. Lower vehicle until tires are touching ground
    注
    Raise lift off locks, then hold lock release lever to keep locks free while vehicle is lowered
  45. Torque RH front wheel
    注
    5x nuts, 21mm, 175 Nm
  46. Install RH front wheel center cap
    注
    1x cap, Verify emblem is aligned with valve stem
  47. Install RH footrest panel
    注
    Rotate RH footrest panel onto vehicle, Fold RH primary support carpet down
  48. Secure RH footrest panel
    注
    2x bolts, 10mm, 5 Nm, 2x nuts, 10mm, 5 Nm
  49. Secure harness to RH footrest panel
    注
    1x clip
  50. Fold RH main carpet back into place
  51. Install RH footwell cover
    注
    3x magnets, 4x datums, 1x connector
  52. Install RH lower A-pillar trim
    注
    1x bolt, T25, 5 Nm, 2x clips, 1x datum
  53. Install RH mid A-pillar trim
    注
    2x clips, 3x datums, Verify weather seal is seated properly
  54. Install RH IP end cap
    注
    3x clips
  55. Install RH front door sill trim panel
    注
    8x clips, 3x datums, Verify seal is seated properly
  56. Install RH console side carpet
    注
    11x clips, 2x datums
  57. Install RH front floor mat
  58. Install the wiper module. See 雨刮器模块（拆卸和更换）.
  59. Install the underhood storage unit. See 前备箱储物单元（拆卸和安装）.
  60. Press brake pedal to turn on drive rails
  61. Turn steering wheel back to center
  62. Set air suspension ride height to “Medium”
    注
    Using center display, Controls > Suspension > ''Medium'
  63. Activate Service Mode using the touchscreen.
  64. Unlock Gateway
    注
    After vehicle has been put into "Service Mode", place keycard on center console to turn on drive rails, hold down the brake pedal, while keep pressing right hand signal button simultaneously for at least 10 seconds, "GTW UNLOCKING" should pop up on the UI right next to the VIN during these 10 seconds, once gateway is unlocked "GTW UNLOCKED 5400" will be displayed on the UI next to the VIN, the gateway will remain unlocked for 90 minutes, follow steps on Toolbox article #5582900 for any additional information
  65. Reset DAS via Service UI
    注
    In Service mode navigate to Driver Assist > Cameras > Reset DAS
  66. 运行 ODIN 例行程序 PROC_ICE_X_EXIT-SERVICE-MODEvia Toolbox:(link)
  67. Raise both front windows.
  68. Close the LH front door.
  69. Vehicle will need to be driven by customer to complete the calibration procedure. During this time DAS functions will be completely unavailable