2026-11-17

Harness - Instrument Panel (Remove and Replace)

Correction code 17100602 2.46 NOTE: Unless otherwise explicitly stated in the procedure, the correction code and its associated FRT reflect all of the work required to perform this procedure, including the linked procedures. Do not stack correction codes unless explicitly told to do so. NOTE: See Flat Rate Times to learn more about FRTs and how they are created. NOTE: See Personal Protection to make sure proper PPE is worn when performing the below procedure.

  • 2026-11-17: Updated the procedure to remove the cross car beam together with the IP harness first, and then remove the harness.
  • 2026-06-18: Added note about the diagnostic port location when installing harness 2552571-01-B or newer.
  • 2025-09-11: Reordered installation steps.
  • 2023-09-25: Corrected links for touchscreen removal in Remove and Install section.
Warning
This procedure is a DRAFT. Although it has been validated, Warnings and Cautions might be missing. Follow safety requirements and use extreme caution when working on or near High Voltage systems and components.
Note
If installing harness PN 2552571-01-B or newer on Model X built before April 2024, the RJ45 diagnostic port at the center console will be deleted. In this case, the OBD-II port can be used for diagnostics. See Toolbox (Connect and Disconnect).

Remove

  1. Open all four doors.
  2. Lower the LH and RH front windows.
  3. On the touchscreen, tap Controls > Steering, and use the left steering wheel scroll wheel to adjust the steering column fully outward and fully down.
  4. Remove the underhood storage unit. See Underhood Storage Unit (Remove and Install).
  5. Remove the wiper module. See Wiper Module (Remove and Replace).
  6. Remove the bolts (x2) that secure the upper steering column bracket IP carrier at the bulkhead.
    Note
    Use of the following tool(s) is recommended:
    • 13 mm deep socket
    • Flex head ratchet/flex head torque wrench
  7. Remove the center console assembly. See Center Console Assembly - 1st Row (Remove and Install).
  8. Disconnect LV power. See LV Power (Disconnect and Connect).
  9. Remove the LH and RH instrument panel end caps. See End Cap - Instrument Panel - LH (Remove and Replace).
  10. Remove the LH and RH middle A-pillar trims. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  11. Remove the LH instrument panel LH middle trim. See Trim - Middle - Instrument Panel - LH (Remove and Replace).
  12. Remove the LH and RH lower A-pillar trims. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  13. Remove the driver knee airbag. However, do not remove the components from the knee airbag assembly after the assembly has been removed from the instrument panel. See Knee Airbag - Driver (Remove and Replace).
  14. Remove the LH and RH sun visor bezel A-pillar trims. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  15. Remove the LH and RH upper A-pillar trims. See Trim - A-Pillar - Upper - LH (Remove and Replace).
  16. Fold the RH front cabin carpet aside for access.
  17. Release the clip that attaches the electrical harness to the RH footrest panel.
  18. Remove the bolts (x2) and nuts (x2) that attach the RH footrest panel to the body.
    5 Nm (3.7 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  19. Remove the RH footrest panel from the vehicle.
    Note
    Fold the RH primary support carpet up, and then rotate the footrest panel out of the vehicle.
  20. Remove the instrument panel service panel from the center console as an assembly. However, do not remove the cabin temperature sensor fan from the service panel. See Service Panel - Instrument Panel (Remove and Replace).
  21. Remove the touchscreen. See Touchscreen (HW3) (Remove and Replace) or Touchscreen (HW4) (Remove and Replace).
  22. Release the tabs (x4) that attach the instrument panel closeout panel to the instrument panel, and then remove the closeout panel from the instrument panel.
  23. Remove the RH instrument panel middle trim. See Trim - Middle - Instrument Panel - RH (Remove and Replace).
  24. Remove the main instrument panel decor. See Decor - Instrument Panel - Main (Remove and Replace).
  25. Remove the front passenger knee airbag as an assembly. However, do not remove the components from the knee airbag assembly after the assembly has been removed from the instrument panel. See Knee Airbag - Front Passenger (Remove and Replace).
  26. Remove the glove box. See Glove Box (Remove and Replace).
  27. Remove the front passenger instrument panel duct. See Duct - Instrument Panel - Front Passenger (Remove and Replace).
  28. Remove the bolts (x2) that attach the instrument panel carrier cross beam.
    3 Nm (2.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  29. Disconnect the front passenger airbag electrical connectors (x3).
    Note
    Pull down the spring loaded locks simultaneously to release the airbag electrical connectors.
  30. Remove the RH lower instrument panel screws (x3).
    3 Nm (2.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  31. Remove the center lower instrument panel screws (x6).
    3 Nm (2.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  32. Remove the LH lower instrument panel screws (x3).
    3 Nm (2.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  33. Release the instrument cluster electrical harness clip, and then disconnect the electrical connector.
  34. Release the instrument panel trim electrical harness, and then disconnect the electrical connector.
  35. Position the lower instrument panel assembly away from the instrument panel sub-assembly.
    Note
    Datums (x6).
    Note
    Move the top edge as far rearward as possible without excessive stress on the assembly.
  36. Release the instrument panel ground harness clip, and then remove the ground harness bolt.
    9 Nm (6.6 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
    Note
    Take note of the harness routing behind the RH touchscreen bracket.
  37. With an assistant, remove the instrument panel sub-assembly.
    Note
    Slide the instrument panel sub-assembly rearward, and then lift the assembly up from the instrument panel carrier.
    Note
    Make sure the airwave vents and front passenger airbag are clear of lower instrument panel assembly.
    Note
    Remove the instrument panel sub-assembly out through the RH front door.
  38. Remove the driver instrument panel duct. See Duct - Instrument Panel - Driver (Remove and Replace).
  39. Remove the driver outboard jumper duct. See Duct - Jumper - Outboard - Driver (Remove and Replace.
  40. Remove the driver airbag. See Airbag - Driver (Remove and Replace).
  41. Remove the steering yoke/wheel. See Steering Yoke/Wheel (Remove and Replace).
  42. Remove the steering column upper shroud. See Shroud - Upper - Steering Column (Remove and Replace).
  43. Remove the steering column lower shroud. See Shroud - Lower - Steering Column (Remove and Replace).
  44. Remove the lower instrument panel. See Instrument Panel - Lower (Remove and Replace).
  45. Release the clips (x3) that attach the instrument panel electrical harness to the J12 x055 dash connector at the RH body controller, and then disconnect the electrical connector.
    Note
    Release the lock, and then remove.
  46. Disconnect the instrument panel electrical harness connector X873 at the top RH side of the car computer gaming board.
    Note
    Release the lock on the electrical connector before removal.
  47. Disconnect the car computer electrical connector.
    CAUTION
    Press the lock on the underside of the electrical connector before pulling out of the socket. Possible damage to the PCBA may occur if removed without releasing lock first.
  48. Disconnect the steering column control module electrical connector.
    Note
    Remove the retaining clip on the electrical connector, then release the electrical connector, and then remove the remaining broken clip the electrical connector.
    Note
    Discard the retaining clip after removal.
    Note
    Originally installed clip is black; replacement clip is orange.
  49. Disconnect the instrument panel electrical harness connector x947F.
    Note
    Release the locking tab before removal.
  50. Remove the bolts (x2) that attach the instrument panel cowl link.
    6 Nm (4.4 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
    Note
    Only remove the bolts from the instrument panel carrier and the HVAC assembly.
  51. Remove the nuts (x4) that attach the steering column to the steering column bracket, and then rotate and set aside the steering column.
    15 Nm (11.1 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm deep socket
  52. Remove the bolts (x2) that attach the LH side of the cross car beam.
    27 Nm (19.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm socket
  53. Remove the bolts (x2) that attach the RH side of the cross car beam.
    27 Nm (19.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm socket
  54. Remove the bolts (x2) that attach the cross car beam to the toeboard bracket.
    27 Nm (19.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm socket
  55. Remove the bolts (x4) that attach the cross car beam to the HVAC assembly.
    8 Nm (5.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  56. Remove the cross car beam from the body and the HVAC assembly.
    Note
    Datums (x4).
  57. With assistance, remove the cross car beam assembly from the vehicle.
    Note
    Be careful not to contact with the seats and the inner door panel.
  58. Release all remaining clips (x19) to remove the instrument panel harness from the cross car beam assembly.
    Note
    Flip the cross car beam over to release the clips if needed.

Install

  1. Route and install the instrument panel harness to the cross beam assembly.
    Note
    19 x clips.
  2. With an assistant, install the cross car beam into the vehicle.
    Note
    Datums (x4).
    Note
    Avoid contact with seats and inner door panel.
    Note
    Align the datums before fully engaging with the HVAC assembly.
  3. Engage the cross car beam to the body and the HVAC assembly.
    Note
    Datums (x4).
  4. Install the bolts (x2) that attach the LH side of the cross car beam.
    27 Nm (19.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm socket
  5. Install the bolts (x2) that attach the RH side of the cross car beam.
    27 Nm (19.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm socket
  6. Install the bolts (x2) that attach the cross car beam to the toeboard bracket.
    27 Nm (19.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm socket
  7. Install the bolts (x4) that attach the cross car beam to the HVAC assembly.
    8 Nm (5.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  8. Install the bolts (x2) that attach the upper steering column bracket instrument panel carrier at the bulkhead.
    27 Nm (19.9 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm socket
  9. Install the nuts (x4) that attach the steering column to the steering column bracket.
    15 Nm (11.1 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 13 mm deep socket
  10. Install the bolts (x2) that attach the instrument panel cowl link.
    6 Nm (4.4 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
    Note
    Datums (x2)
  11. Fasten the clips (x5) that attach the instrument panel harness to the J12 x035 Dash connector at the LH body controller, and then connect the electrical connector.
  12. Connect the instrument panel harness electrical connector x947F.
    Note
    Secure the locking tab after installation.
  13. Connect the steering column control module electrical connector.
    Note
    Install a new orange retaining clip to electrical connector, and then install the steering column control module connector. Perform a push-pull-push to make sure connector is seated properly.
  14. Secure the instrument panel harness to the lower right of the instrument panel carrier.
  15. Fasten the clips that attaches the glove box USB cable to the instrument panel carrier.
  16. Connect the instrument panel harness connectors (x5) at LH side of the car computer gaming board.
  17. Connect the car computer electrical connector.
    Note
    Confirm the connector is locked into the socket.
  18. Fasten the clips (x3) that attach the instrument panel harness to J12 x055 Dash connector at the RH body controller, and then connect the electrical connector.
  19. Connect the instrument panel harness connector x873 at the top RH side of the car computer.
  20. Install the driver outboard jumper duct. See Duct - Jumper - Outboard - Driver (Remove and Replace.
  21. Install the driver instrument panel duct. See Duct - Instrument Panel - Driver (Remove and Replace).
  22. With an assistant, install the instrument panel sub-assembly.
    Note
    Slide the instrument panel sub-assembly into the vehicle.
    Note
    Make sure the front passenger airbag and the driver vent assembly have clearance past the lower instrument panel assembly.
    Note
    Engage the instrument panel sub-assembly datums into the dash slots.
  23. Connect the instrument panel trim harness electrical connector.
    Note
    Clip (x1)
  24. Connect the instrument cluster harness electrical connector.
  25. Position the lower instrument panel assembly into the instrument panel sub-assembly.
  26. Install the LH lower instrument panel screws (x3).
    3 Nm (2.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  27. Install the center lower instrument panel screws (x6).
    3 Nm (2.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  28. Install the RH lower instrument panel screws (x3).
    3 Nm (2.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
  29. Fasten the tabs (x8), and then install the screws (x3) that attach the lower instrument panel.
    3 Nm (2.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • Torx T20 bit
    Note
    Secure only the screws located at the bottom of the assembly. The remainder of screws are fastened at a later step.
  30. Install the main instrument panel decor. See Decor - Instrument Panel - Main (Remove and Replace).
  31. Install the steering column lower shroud. See Shroud - Lower - Steering Column (Remove and Replace).
  32. Install the steering column upper shroud. See Shroud - Upper - Steering Column (Remove and Replace).
  33. Install the bolts (x2) that attach the instrument panel carrier cross beam.
    3 Nm (2.2 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  34. Connect the front passenger airbag electrical connectors (x3).
  35. Install the front passenger instrument panel duct. See Duct - Instrument Panel - Front Passenger (Remove and Replace).
  36. Install the glove box. See Glove Box (Remove and Replace).
  37. Install the RH footrest panel.
    Note
    Rotate the RH footrest panel into the vehicle. Fold the RH primary support carpet down.
  38. Install the bolts (x2) and nuts (x2) that attach the RH footrest panel to the body.
    5 Nm (3.7 lbs-ft)
    Tip
    Use of the following tool(s) is recommended:
    • 10 mm socket
  39. Fasten the electrical harness clip to the RH footrest panel.
  40. Fold the RH main carpet back into place.
  41. Install the front passenger knee airbag. See Knee Airbag - Front Passenger (Remove and Replace).
  42. Install the RH lower A-pillar trim. See Trim - A-Pillar - Lower - LH (Remove and Replace).
  43. Install the RH front sill. panel trim. See Trim - Sill Panel - Front - LH (Remove and Replace).
  44. Install the RH upper A-pillar trim. See Trim - A-Pillar - Upper - LH (Remove and Replace).
  45. Install the RH sun visor bezel A-pillar trim. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  46. Install the RH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  47. Install the RH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  48. Install the RH instrument panel middle trim. See Trim - Middle - Instrument Panel - RH (Remove and Replace).
  49. Fasten the tabs (x4) that attach the IP closeout panel.
  50. Install the touchscreen. See Touchscreen (HW3) (Remove and Replace) or Touchscreen (HW4) (Remove and Replace).
  51. Install the instrument panel service panel. See Service Panel - Instrument Panel (Remove and Replace).
  52. Install the LH upper A-pillar trim. See Trim - A-Pillar - Upper - LH (Remove and Replace).
  53. Install the LH sun visor bezel A-pillar trim. See Trim - A-Pillar - Sun Visor Bezel - LH (Remove and Replace).
  54. Install the LH instrument panel middle trim. See Trim - Middle - Instrument Panel - LH (Remove and Replace).
  55. Install the driver knee airbag. See Knee Airbag - Driver (Remove and Replace).
  56. Install the LH middle A-pillar trim. See Trim - A-Pillar - Middle - LH (Remove and Replace).
  57. Install the LH instrument panel end cap. See End Cap - Instrument Panel - LH (Remove and Replace).
  58. Install the steering yoke/wheel. See Steering Yoke/Wheel (Remove and Replace).
  59. Install the driver airbag. See Airbag - Driver (Remove and Replace).
  60. Install the wiper module. See Wiper Module (Remove and Replace).
  61. Reconnect LV power. See LV Power (Disconnect and Connect).
  62. Install the underhood storage unit. See Underhood Storage Unit (Remove and Install).
  63. Install the center console assembly. See Center Console Assembly - 1st Row (Remove and Install).
  64. Adjust the steering column back to its original position.
  65. Calibrate the LH and RH rear doors by holding each upper B-pillar button in the down position.
  66. Close the RH front door.
  67. Raise the LH and RH front windows.
  68. Close the LH front door.